FGQ1442ES3 Frigidaire Dryer - Instructions

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again

I recently ordered parts for a gas dryer, Frigidaire GLGQ2152 ES3. When I received an igniter part number PS12585650 order number 14700077, the igniter was broken when I opened the box. I believe what happened is that the new metal bracket was wrapped in the bubble wrap along with the igniter. I called customer service and was setup to return the igniter which I did. Also, I ordered a second igniter. I receive the second one and it wasn't broken and the bracket was outside the bubble wrap during shipment.

As far as the installation of the "replacement" igniter into the gas dryer, I could not find instructions on how to install it. The received igniter is much different than the original. There was a small instruction sheet stating that the new igniter is different but can be installed using the new bracket that came with the igniter. But again there were no instructions on how to do this. It took me great effort to figure out how to do this.

The old igniter had to be removed by removing the old bracket assembly that the igniter was mounted on. The new igniter had to be installed onto the new bracket and then by sliding the new assembly under the old assembly, the screws were reinstalled. Although the holes where the original screws were to be screwed into were too small, they had to be drilled out. There was no hardware (screws) to install the "replacement" igniter onto the shipped bracket.

After much work, I finally got the new igniter installed (without breaking it) with the new bracket and the dryer is back in operation.

Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Followed the video as my unit was exact model( Front Loader) Thank You for your quick ship to me here in Iowa as my repair was made in St. Louis. Parts came with in 2 days then drove to St. Louis with confidence. We purchased this set in 2003 and it is first repair on dryer. This in my rental unit. Thx

First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work.
Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

I followed the instillation instructions provided on your website. They were very informative and spot on. My only problem was my strength. I could not get the drum off of the rear bearing myself, but then I am a 61 year old female.

Just like in the video, but with a stackable washer/dryer unit, works like new now....

Had to open back side vent & use needle nose to secure spring.