FASG7074LW0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lukas from Pasadena, CA
- Parts Used:
- 5303207102, 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
latch broken
pulled out old catch with old pliers and popped new one, simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Scottsdale, AZ
- Parts Used:
- 137553402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer gasket keeps coming off
Such an easy repair that I should have done months ago. I knew the gasket was failing but kept fixing the old one until it finally broke apart and couldn't be reused. The new gasket installed within minutes and fit perfectly, not to mention I no longer have to deal with it every time I do the laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Brooklyn, NY
- Parts Used:
- 5303931775
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat
Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from Silver City, NM
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The Heating System Of The Propane Dryer Stopped Working
When I direct the dryer exhaust into the room during the winter there is an external lint filter in the ducting. For some reason,enough lint got by the dryers filter and over a few cycles clogged the exhaust. I correctly assumed that the dryer overheated and some thermal limiter had opened up. The manual had exploded views and I located the limiter. Getting to it was another issue. The manual gave nbo instructions on getting to the limiter, but I had installed a propane conversion kit when I first got the dryer. It was necessary to remove the top, control panel, and front panel/door assembly. Disconnecting the gas line,some cable connectors, and a few screws allowed the removale of the burner assembly, then removal of the metal tube that surrounded the burner assembly and held a number of sensors, including the thermal limit, which, as expected, showed an open circuit. The replacement part was ordered and checked out as a closed circuit, which it should. Reassembly was the reverse. A little difficult to work in the cramped lower corner of the dryer. I'm 82 years old now but machines cannot beat me!!
Was this instruction helpful to you?
Thank you for voting!