CAQE7021LW0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- EDWARD W from LA CENTER, WA
- Parts Used:
- 137553402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket became unattached from the dryer door
Very easy lined the slots on the dryer door with the gasket and
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from DULUTH, MN
- Parts Used:
- 137553402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door seal/gasket coming off of dryer door. Could not make it stay as designed.
This was the easiest repair ever done. Pulled out old seal/gasket and popped in new one. Took about 2 minutes. Be sure to mark where ends of new door seal (gasket) starts and ends when removing the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from CHALMETTE, LA
- Parts Used:
- 137553402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old gasket became worn, no longer would hold in place, taking longer to dry
EZ. Viewed you tube replacement video, EZ off and on, applied little heat, closed dryer door, good fit, heat made it fit even better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rey from DONIPHAN, MO
- Parts Used:
- 134786110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would turn off too soon and clothes were not completely dry.
I removed the Moisture sensor from inside the dryer and installed the new one. Two wires are connected to the sensor and it is fastened down with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Payette, ID
- Parts Used:
- 137105100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door hinge very loose
Watched a YouTube video. Very easy to replace, I’m 73 year old woman…this was a very easy job, anyone can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAN FRANCISCO, CA
- Parts Used:
- 5308027429
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ROUND TOP, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The thermostat had deteriorated and no heat
Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from HUDSON, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from PORTAL, GA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our door catch got lost inside the dryer after the door was slammed to hard
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch on dryer no longer worked
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BROOKLYN, NY
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Just popped the part I ordered right in and it's was closing in no time !
Just opened package and popped the part right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from WALLA WALLA, WA
- Parts Used:
- 3204267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
lack of heat
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mathew from CHELMSFORD, MA
- Parts Used:
- 5304508449
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer was leaving marks on clothing
You must disconnect appliance from the gas, water and vent to access the back. Remove the top of the dryer which then allows you to remove the rear panel by removing all screws, You may also have to remove 2 electrical connections to get this panel off. Now you have access to the air duct. To remove the air duct there are 3 screws inside the dryer and 2 screws on the lower part of the air duct. One of the lower screws is facing toward the inside of the dryer and you will need a 12"+ screwdriver to be able to remove. Once you do all that install the new part and repeat steps in reverse.
Was this instruction helpful to you?
Thank you for voting!