FSE848RHS0 Frigidaire Dryer - Instructions

Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.

Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.

I unplugged the dryer and then removed the top sheet metal cover with a nutdriver. I removed old timer with a phillips #2 screwdriver. I drew a diagram showing which color wires were connected to each point on the old timer. I unplugged the wires (a needle nose plier was needed for some of the tighter connectors) from the old timer and then connected the new timer. The whole repair would have been less than 30 minutes, but I dropped a screw into the open dryer. I had to remove the front sheet metal to retrieve the screw. This was the only annoying part and probably doubled the repair time, but even this was not too hard. I hate this dryer and will never buy another Fridigaire appliance, but I am happy with the quick service of PartSelect.com. It was faster and a lot cheaper for me to buy the part and do it myself instead of scheduling a repair.

Called a repair co. Said it would be about a week before he came to the rural area my mom lives and he probably wouldn't have the part. He would order it after he determined the problem. So I went to your web site and ordered the item it said was 80% and two other parts just in case. He came and used the Heating Element Assembly and said it was a good thing we had it. He would have had to order it and come back probably a week later. THANK YOU!! WE needed the dryer repaired sooner and saved another service call. I am returning the other parts not used and you make it so easy to do. I plan on using your site again.

Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.

Thanks.

First, I read the other posts and got a good idea as to how to do it. I needed to replace the upper felt and guides but decided to go ahead and replace the lower felt and the bearing holder as well. If I had been thinking I would have replaced the belt at the same time but, oh well.

Disconnect the electric plug from the wall.
Pop the top using a medium sized flat head screwdriver.
Disconnect the wiring harness at right front of the unit.
Remove the two screws near the top of the front panel and squeez the retaining clips. You may need a pair of pliers for this but be gentle.
Pull straight up on the front panel to remove it.
To get to the bearing holder, remove the drum by first removing the access panel located at the rear of the dryer and removing the belt from the springloaded plastic pulley. With no tension on the belt simply pull up on the drum while also pulling slightly forward. The drum will pop right out but you will have to apply some pressure. There is no need to remove the three screws at the back of the drum on the inside.
Once the drum is out, remove the two screws holding the bearing holder and remove the assembly being careful not to lose the single ball bearing at the rear of the assembly. Pay attention as to how the assembly goes together.
Scrape off the old felt and glue. Like everyone else, I used a chisle and some GOOP. The old felt came right off with little effort and the GOOP cleaned off the old glue with not too much effort.
Apply the glue that comes with the felt glides according to the instructions on the tube. There's plenty to do both upper and lower felt in that tube. I used some spring clamps to firmly set the upper felt. The glue sets in just a few minutes. The lower felt has a bevelled edge that goes toward the door and fits into a groove on the panel. Once the glue is set you you are ready to put it back together. Like everyone else, I took the time to vacuum out the interior of the dryer and collect the coins and buttons that had accumulated. I found it very easy to reinstall the bearing holder assembly by myself by working from the side of the dryer. I put a dab of grease on the single ball bearing to hold it in place while I reinstalled the assembly. Put some grease in the bearing holder and reinstall the drum, then the front panel and belt. Put the belt back on the tensioner and take care of the couple of lose end and you're done.

This is a "no big deal" repair that looks worse than it is. It took me about 2.5 hours to complete and I was taking my time and just enjoying the fact that I was doing it myself.

Our heating element went out on our Frigidaire Affinity dryer. My husband is good at repairing things so we decided to order the part and do the repairs rather than hire a service technician. Before looking at the dryer we thought the back could be unscrewed and taken off to give access to the element but it did not. He had to take the dryer drum out to access the element. It was easy enough for him to do though and since we had everything opened up I was able to use the shop vac to get all lint cleaned out. I'm glad he did have to take the drum out after I realized the gasket on the exhaust pipe wasn't fitted on properly. There was some lint where there should not have been. Now that everything is clean and we have the new heating element installed we are good to go! The whole process of taking apart, installation and putting back together took about an hour and 15 minutes so not bad and we only had to pay for the part and shipping! Thanks PartSelect!

followed the instructions video on the site had no problems just took about 2 hrs to complete

Just put on the new knob! Supper easy and it works great!

Took it out of the bag and put it on.

Simply popped it back into place, careful not to break the new handle.

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.

All I had to do was line the "D" shaft up with the "D" metal shaft on the Dryer and push the knob on. I made sure it would turn properly, and turned the Dryer on the make sure it worked. All is good.

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Just snap into place