DE700EDH5 Frigidaire Dryer - Instructions

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

FOLLOW THE VIDEO!! I was scared to even get into it until I watched the video. Made it easy for me and I have little to no mechanicl skill. Excellent video that made it super easy. Took me an hour as I was taking my time. Now I could probably do the same repair in 20 minutes.

googled frididaire dreyer parts
found Partselect
ordered parts {they were here in less time than what they stated}
watched Film {very helpful}
Me and My son installed both parts less than 1 hr.
VERY HAPPY WITH PARTS AND SERVICE
Will order from PartSelect when something else Breaks
VERY happy
Dave..

First I have to say that the video on the Parts Select website was invaluable, it truly made the replacement a no brainer. The kit came with everything I need and was a great price.

Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.

I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.

Followed the video on partselect web page.

Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.

I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful

1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble

I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!

Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.

Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.

A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!

The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).

But, I highly recommend Partselect!!!!

First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

We had the rear drum bearing replaced about three years ago. The company that serviced it was quick to take our money for the diagnosis but took over a month (and a threat to call the better business bureau) to actually make the repair. This time I decided to do it my self as I had successfully replaced the the drum drive belt two years ago. The dissassembly was challenging but the repair it's self very easy. I opted to use nuts and bolts to attach the bearing assembly rather than the supplied screws as they did not want to tighten. Reassmbly was a bit of a challenge regarding the drum drive belt but I had the entire repair done in less than an hour.