CGR3600AS3 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gigi from great neck, NY
- Parts Used:
- 131622202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the lint cover trap came off and broke
we simply screwed the new one in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Sewaren, NJ
- Parts Used:
- 5303937183, 137513300
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Black lines and small tears
Previous comments on line were so helpful.
My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.
Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.
My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.
Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miles from LaPorte, IN
- Parts Used:
- 5303281153
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Loud Squeek while the dryer is running.
1. After checking the Parts Select website for some useful information I unplugged the dryer.
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't tumble with normally large load - very noisy when it did tumble
I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.
The internet is a magnificent thing!
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.
The internet is a magnificent thing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Fairfield, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heat would initially come on then go off or sometimes not come on at all.
1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Emporia, KS
- Parts Used:
- 137513300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Front drum guidesnubber ring was worn out
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from lake worth, FL
- Parts Used:
- 137513300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
clothes were getting stuck
after numerous holes put in my families clothes i looked on line and found "partselect.com". i ordered the front drum glide after seeing a similar story about the clothes being torn and getting caught and my family and i have our new dryer back!! yeah :<)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from San Francisco, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No heat.
As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAN FRANCISCO, CA
- Parts Used:
- 5308027429
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- garland from Morganton, NC
- Parts Used:
- 134503600, 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not spin
After unplugging the dryer, disconnecting it from the vent, and moving into an open work area, I popped the top open with the blade of a screwdriver, disconnected the two wires that connect to the door switch, then lifted the front panel (with the door) up and away from the drum. Next, I lifted the drum out of the worn rear bearing assembly and lowered it into the dryer in order to release tension on the belt. I then removed the entire drum by carrying it forward and out of the way. I then removed the old bearing assembly, which was loose and covered with metal dust. After cleaning the area with a dry cloth to remove the old grease and metal dust, and vacuuming all the lint off *everything*, I installed the new bearing assembly with a 5/16" nut driver, being careful to position the provided ball-bearing between the plastic bearing assembly and the outer clip. The little ball-bearing is very important, as it is the drum's only path to ground, and prevents the build up of static electricity as the drums spins. I then filled the new bearing assembly with the provided grease. Everything is easy up to this point, but the difficult part for me was removing the old hub from the drum and re-attaching the new one. It is held on by three screws and they become seated very tightly. After loosening them and removing the old hub from the drum, attaching the new one prvoed difficult as well, as the screw-holes in the new hub are not threaded to fit the screws. The screws muct be forced to cut a thread as you install them, which requires a great deal of force. After installing the new hub and putting the new belt (pruchased separately) around the drum, the next step is to reinstall the drum by lifting it in through the front of the dryer and positioning the new hub over the new bearing assembly and pressing it down into place. It will gently "snap" into place as it seats. Then, on the back side of the dryer, I removed the vent panel by removing the two screws that hold it in place and positioned the new drive belt (loosely dangling around the drum) over the motor's drive wheel and behind the sring-tensioned idle arm. Then it is a simply matter to reinstall the front panel by genly lifting the drum and sliding the door opening inside it, then reseating all the little clips that hold the front panel in place. I then pressed the top back into place, reconnected the vent hose, plugged it back in and checked for operation. My fifteen year-old dryer now works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giuseppe from San Francisco, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas flame turns off after a while, dryer keeps turning but no heat is generated.
Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.
1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.
This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!
1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.
This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from BELLEVUE, MI
- Parts Used:
- PCK2003
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dryer needed to be converted from natural gas to propane
The conversion kit had everything needed, However the instructions were lacking in description on how to assemble everything, this kit includes the new style burner, igniter, igniter mount, air shutter and propane orifices. A detailed picture would help.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson Falls, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud Squealing
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelia from Elizabethtown, IL
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
replaced broken belt
Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!
Was this instruction helpful to you?
Thank you for voting!