FSG747GES0 Frigidaire Dryer - Instructions

Based on all of the other posts, their explanations were right on, so I won't repeat it here. You could probably do this repair on your own, but it helps having someone to hold the drum while reattaching the screws. I replace the rear drum bearing assembly and the belt. I would recommend replacing the belt. I almost didn't, but I'm glad I did. Once I had it off, I could see the cracks in it.

When installing the new bearing, make sure that you pack it with the supplied grease. Be liberal with it. I used what left over grease I had to grease the idler puller bearings too.

The dryer works perfectly now, with no squealing. My experience with Parts Select was flawless. The shipping was extremely fast, and the parts were as described. Finding the correct parts was a snap thanks to their easy to use web site.

1. Released the front latches under the dryer top and flipped it up.
2. Removed two screws holding the dryer front in place and flipped it down.
3. Tore off old drum glide and lower seal.
4. removed most of the remaining fuzz with sandpaper.
5. Glued the new seals in place.
6. Put everything back together.

All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.

Much cheaper than a new dryer!

First I unplugged the dryer. I removed the 3 knobs on the front control panel as well as the 6 screws on the back. The start switch easily removes by turning it 45 degrees and pulls out. I used a pair of needle nose pliers to pull the two connectors loose from the old switch. (They are color coded wires, 1 brown and 1 gray. The switch is marked with the numbers 1 and 2 on the connectors so remember which one goes where) Then i hooked up the new switch in reverse order and was back in business in about 5 minutes.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

Removed the front, door and all. Replaced both upper and lower seals and allowed glue to dry for 24 hours. Removed 3 screws attaching drum to pivot in rear. While drum was out, relubricated pivot seat and ball. Installed new drum which has been re-designed, has strip around entire lip now. Seals are different, so both have to be replaced with ones in kit, supplied tube of glue is not enough to do the job, so used gator glue. Had trouble installing the 3 screws that attach it to the pivot. Finally re-assembled entire front panel and replaced the door. Started the dryer and it worked as new.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

the old one had fallen off ages ago and I was using pliers to start the dryer. If I had known how easy/cheap it was to find the part on this website and replace it, I wouldn't have waited so long. All I did was push the knob onto the rod that sticks out of the dryer panel. easy as pie

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

All I did was push the new part into the machine! So easy!

This was a Sears Dryer, also know as Kenmore, This dryer can be stacked or side by side. In this case it was stacked. There are no directions on how to replace this part. For this model made in 2005 the lid of the dryer is held in front by two clips. You open the lid simply by prying the two front corners up with a flat head screw driver. The front of the top lid pops right up. You may have to remove the mounts in back if you cant lift the dryer lid enough to be able to get your hands in. UNPLUG THE DRYER I got a nasty shock. There are two wires on the switch, remember how they go and where they are, that's important. Turn the switch (from the front or back) so that it pops out. Remove and replace the wires put it back in (from behind/top) and twist a 1/4 turn into place. Plug, test and simply push the cover back down onto the clips. Done.