FDE546RET0 Frigidaire Dryer - Instructions

First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.

First of all, I LOVE Partselect.com.. The parts are reasonable, and arrive in a timely fashion.. The repair stories are far and away, one of the BEST features of this website - so hats off to the DIY'ers who have helped me overcome my challenges and helped me stay in the ..ahem.. "favorable" graces of my wife.. I need all the help I can get there.. Anyway, read the other repair stories first - LOTS of great insight.. I only have a couple pointers to add - below...

This is easily my 4th appliance repair project with Partselect.com, and I can say without a doubt that the experience has been positive every single time.. Until now.. I got the dryer torn down and realized that I SHOULD have ordered the SEAL-BASKET LOWER felt with my original order. When I inspected it for my list of parts to order, the upper glide was thrashed - no brainer.. I thought the lower felt was fine.. d'oh! I discovered this morning that I was wrong.. So, I JUST ordered the lower basket seal for *next* weekend.. (If you are gonna replace the original upper glide, replace the lower basket seal as well..) It'll be a slam dunk, though..

Now, for a couple useful tips:

If you are a car guy, get out your trusty can of brake parts cleaner to help clean off the old adhesive residue after you rip off the old upper glide felt. I also used a 1" plastic scraper to help facilitate removal, but the brake parts cleaner was a Godsend. I think I read someone else's suggestion to use "goof off" or whatever - but I couldn't find mine, so..... ...out came the brake cleaner... :) two thumbs up. Just use it sparingly - all those solvents are bad for children in California for some odd reason..

Spring loaded clamps to hold the felt down as the glue dries are also "nice to have". I used one on each end of the felt, and one for each of the teflon / plastic glides..

Finally - milk this job for all it's worth - it'll only take you 45-60 minutes or so... good luck...!!!

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply
front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

Removed the door and replace the upper glide and the lower seal. The repair was easy.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

popped in one in

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover

I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.

First I removed the 2 screws on the back. These 2 screws hold the top cover. I also used a flat screw driver to press the 2 locks that hold the top cover, they are located in front and under the top cover . Then I removed the 2 screws that hold the front cover. After removing the front cover I replaced the drum glider and the seal-basket lower. Now my dryer is working perfectly...