FDG747RET0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- chris from dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch on dryer no longer worked
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cumberland, RI
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clothing was getting caught between drum and front panel
First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike
Mike
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portsmouth, RI
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer squeak during tumbling, worn front drum glide
Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.
A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.
Fit of new glide was straightforward and fit well to the lower felt glide..
(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.
Fit of new glide was straightforward and fit well to the lower felt glide..
(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Auburndale, MA
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer was snagging clothes between the drum and frame
Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.
Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.
Reverse the first paragraph to re-install.
Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.
Reverse the first paragraph to re-install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHARON from SUMMERVILLE, SC
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Dryer making horrible squeaking sound when running
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from New Roads, LA
- Parts Used:
- 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bearing bad and shaft broken
replaced bearing and shaft new belt and everything works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from richmond, MO
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
read shaft and bearing wore out..screaching bad
I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Topsham, ME
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Brown stains on clothes
Removed the door and replace the upper glide and the lower seal. The repair was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Camby, IN
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
burn marks on clothes
Taking apart the dryer was easy. Pop the top, take out two screws, separate the front panel from the drum. Removed the old felt seals but much remained. Used a wire wheel on my drill to clean off felt and old glue (most difficult part). Applied new glue,used a band clamp, one hour later I reassembled the dryer; works fine. No more burn marks on clothes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from New Bern, NC
- Parts Used:
- 131553800
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt was broken drum wouldnt turn
disconnect power and remove front panel and controls.
Remove old belt and reassemble. Had trouble getting the front drum seal with the load bearing glides to fit as trying to replace the screws that supported it. Getting the belt under the motor to the pulley which is beween the mottor and the blower is a trip.
Anyway done and working. Thanks for being there with the poarts at a fair price
Remove old belt and reassemble. Had trouble getting the front drum seal with the load bearing glides to fit as trying to replace the screws that supported it. Getting the belt under the motor to the pulley which is beween the mottor and the blower is a trip.
Anyway done and working. Thanks for being there with the poarts at a fair price
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Wisconsin Rapids, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum making noise when running ( rear bearing )
Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RACINE, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer making metal on metal noise....
Just like in the video, but with a stackable washer/dryer unit, works like new now....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott D from East Fallowfield, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Thump or clang at regular intervals while in operation
UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.
I can attest to this system only on my model since this is the second bearing I have done.
Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.
I can attest to this system only on my model since this is the second bearing I have done.
Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Oak Park, IL
- Parts Used:
- 134417000, 5303937139, 5303283286, 131553800
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clothes getting caught in the drum and getting rust stains
Looking from the front at the top cover I lifted the cover with my fingers and inserted a screw driver about one or two inches from each edge.
The top pops loose and lifts up like the hood of a car.
Inside the dryer on either side behind the front panel there is one screw on each side. Remove the screws and lift the entire panel and door. Then swing the assembly out like a door with a hinge on the right. It won't come off due to the wiring harness.
Make sure you study the upper drum glide before removing it. Remove the upper drum glide using Acetone, this is easy but a little messy.
Apply glue, I applied to the drum but if I did it again I would apply it to the glide and clamp it to the drum in three or four places.
This is an income property and my tenants weren't happy so I didn't wait for the other parts. I don't know now if I really needed them. I will replace them anyway.
I realize they make these things easy to repair. It makes the $200+ they charge that much more profitable.
I also vacuumed and cleaned inside.
This is pretty easy and does not require much skill.
Position the panel on the dryer. There are two clips that need to lined up on the bottom and fit the drum back on. Then snap the top cover in and test the dryer.
Remove the top replace the front panel screws and snap the top back in.
I wish I could post pictures there really isn't much to it.
For property owners I would recommend learning how to do this prior to getting a call.
Create a kit of parts that will wear or break. $100 will save you the hassle of ordering under pressure and get you up and running that much faster.
The top pops loose and lifts up like the hood of a car.
Inside the dryer on either side behind the front panel there is one screw on each side. Remove the screws and lift the entire panel and door. Then swing the assembly out like a door with a hinge on the right. It won't come off due to the wiring harness.
Make sure you study the upper drum glide before removing it. Remove the upper drum glide using Acetone, this is easy but a little messy.
Apply glue, I applied to the drum but if I did it again I would apply it to the glide and clamp it to the drum in three or four places.
This is an income property and my tenants weren't happy so I didn't wait for the other parts. I don't know now if I really needed them. I will replace them anyway.
I realize they make these things easy to repair. It makes the $200+ they charge that much more profitable.
I also vacuumed and cleaned inside.
This is pretty easy and does not require much skill.
Position the panel on the dryer. There are two clips that need to lined up on the bottom and fit the drum back on. Then snap the top cover in and test the dryer.
Remove the top replace the front panel screws and snap the top back in.
I wish I could post pictures there really isn't much to it.
For property owners I would recommend learning how to do this prior to getting a call.
Create a kit of parts that will wear or break. $100 will save you the hassle of ordering under pressure and get you up and running that much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Avis, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud squealing
As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.
The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.
Once I figured that part out, it was a piece of cake.
Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)
The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.
Once I figured that part out, it was a piece of cake.
Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)
Was this instruction helpful to you?
Thank you for voting!