FDE336RBS0 Frigidaire Dryer - Instructions

Pushed the new timer knob on the dryer. No tools were necessary.

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

popped in one in

/removed the lint screen & tossed in the trash, removed one screw from each side of the frame with a screw driver. Placed the New frame in place
& secured it with the screws that I removed from the old frame, placed the screen in place & that was all there was to it. The total amount of time to remove the old & replace with the new probably took 10-15 min. @ the most. I am so happy to have found the part & was able to replace it. You all are wonderful. Received it in 3 days, WOW!!

uncrew old, take out, put new in, screw in place.

Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Lifted broken screen out and replaced it with a new one. Extremely simple.

I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.

Followed the video

Remove top cover and front and remove drum and install a new bearing kit and new belt.

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.