FSEB39RGS0 Frigidaire Dryer - Instructions

I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set aside remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck

I bought part PS419092 (Rotary Knob) for my Firgidaire FDGB23RGS2 Dryer.

This knob I bought (PS419092) is much cheaper than the parts recommeneded for Frigidaire dryers ( knobs: PS417309 and PS416982 ). It is $6 instead of $18.

The only difference is that it (PS419092) is white instead of cream/off-white.

Putting the knob on was super easy and I'm glad I saved money by buying the less expensive part.

I followed the recommendation from William, from Ardmore, OK and Elvis, from Miami, FL for the repairs. Elvis had detailed instructions as well as William, so I just combined the two and I was able to repair my dryer in three hours time. My sincere thanks to partselect web site in posting the repairs on line and for everyones input. I will be back to use the web site again to troubleshoot my other appliances and order parts (great price, fast service for parts) and I will highly recommend this site to my friends.

The new rotary knob just popped right in. No problems. It was a perfect fit.

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!

1. After checking the Parts Select website for some useful information I unplugged the dryer.
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem

This is a stacked wash/dryer.
- unpluged washer/ dryer
- removed front panels under dryer drum area
- disconedted the wiring connection from washer to dryer
- removed front door panel
- disconnected and removed belt
- removed screws holding in drum
- removed drum
- replaced felt on the door (came with drum replacement kit)
- aligned and attached new drum
- replaced belt on drum
- aligned and installed door
- reconnected wiring connecting washer and dryer
- installed fron panels under dry door
- pluged in washer/dryer
Works like new

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

much as described earler,
1. Removed 2 screws on back at the top and 2 on the chrome vent to access the belt and pulley.
2. Disconnected spring from pulley assembly and removed belt from pulley and motor.
3. Removed top of dryer.
4. Removed control panel.
5. Removed screws from inside dryer tumbler (all of them)
6. Removed bottom kick plate.
7. Removed 2 screws from inside panel (near tumbler) and 2 screws from bottom of front panel. Removed front panel.
8. Removed tumbler housing.
9. Removed heating element cover.
10. Removed heating element pan. (wires first)
11. Removed "bearing" by lifing it up (snaps in)
12. Cleaned and regreased "bearing"
Assembled in reverse order.

When it comes to repairs the only thing that I can fix are sandwiches. To say that I am a handy man is usually followed by snickers from my wife and friends... However, I was able to completley take apart my dryer, replace the heating pan and coils, put it back together and it works all by myself (my wife was standing behind me with a fire estinguisher when I plugged it in for the 1st time). I took the advice of some of the post I saw on this sight and took some before shots with my camera phone and marked the wires with tape so I knew where to return them and was able to get it all done. I was suprised at how easy it was to do and how simple a dryer really is on the inside. Ordering the part and doing it myself saved me a couple of hundred dollars easy.... this was the way to go!

There are only three screws holding the drum in. However, to get it out I had to remove the front panels, and the top of the dryer part of the washer-dryer combo. The drum came out easily, but getting the new one in was pretty hard. I had to guess how the drive belt was routed around the motor pulley and idler pulley, since I couldn't see it until I'd removed the drum. Since the new drum wasn't exactly like the old one, I had to remove the glide strip from the front panel to get it to fit. At present, the unit is not completely reassembled, so I can't say I've been entirely successful. Tomorrow, I will put it back together, cross my fingers, and switch it on. Wish me luck!

Followup: The dryer part of this washer-dryer combo is back online. At first, the dryer made a squealing noise, but eventually quieted down. At present, the drum replacement seems to be just fine. It cost about $215, and, except for a few cuts due to sharp-edged metal, a dropped clip that disappeared into the depths of the bottom of the washer, it is actually REPAIRED. I could have used more specific help, but, all in all, it has been pretty easy, and pretty effective.

Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.

Thanks.