FSE748GFS1 Frigidaire Dryer - Instructions

my motor was making noise i tried to replace the motor but could not get the blower wheel off the motor so i had to buy a blower and housing assy. also... now it works great...

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

First I unplugged the dryer. I removed the 3 knobs on the front control panel as well as the 6 screws on the back. The start switch easily removes by turning it 45 degrees and pulls out. I used a pair of needle nose pliers to pull the two connectors loose from the old switch. (They are color coded wires, 1 brown and 1 gray. The switch is marked with the numbers 1 and 2 on the connectors so remember which one goes where) Then i hooked up the new switch in reverse order and was back in business in about 5 minutes.

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.

the old one had fallen off ages ago and I was using pliers to start the dryer. If I had known how easy/cheap it was to find the part on this website and replace it, I wouldn't have waited so long. All I did was push the knob onto the rod that sticks out of the dryer panel. easy as pie

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

While my wife was using the dryer, she noticed a loud sound and sparks coming from the bottom of the dryer (and an elctrical smell). The dryer stopped heating. When I started taking off the top and front of the dryer, I noticed what looked like a thermostat had melted and burned. I called a local part store and they said they would have to order it and it would take two weeks. But the guy was kind enough to give me the part number and told me to call anothe store. Instead I went online, found this site and the next day I had the part. It took me less than an hour to install it and reassemble the dryer. Me and my wife were very pleased.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

Girls you can do it on your own!

The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.

The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place.

It's a breeze!

My dryer's timer stopped moving forward, but everything else worked fine. After looking online it was clear that the timer needed to be replaced.

Note: Use your dryer's model number when ordering, not the model number of the timer (there are multiple versions of the timer, all with the same model).

To replace the timer, I just popped the latches to the dryer's lid by sliding my ruler into the gap between the lid and the front side. With the lid open and the power disconnected , all I had to do was unplug the electrical wires with a plier (for ease), and unscrew the 2 screws behind the timer knob which just pulled off.

My dryer is now working great again!