DG600JXD1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryant from tolna, ND
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer did not turn
put the new part on with ease took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bennie J from Kite, GA
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer making lots of noise
Remove small back plate near floor with 1/4 inch nutdriver unscrewing two screws. Lay the small plate to the side. Remove dryer belt from around pulleys by pulling up on the old idle arm near main spring. This will loosen tension of the belt. Belt just needs to be removed from only around the two pulleys. Detached spring from old idle assembly. The old assembly will just lift out. Reassemble in reverse order with new assembly from Parts Select. Takes less than 5 minutes. Extremely easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jillian from Columbus, OH
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a new lint screen, that's all.
I got my order THE DAY AFTER I ORDERED IT!!!! I didn't expect that. If you can use a screwdriver you can install it. I would use this company again for anything I needed like this. Great service!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clinton from rogersville, TN
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lint screen was torn
I removed two phillips head screws, lifted out the old screen and frame, dropped the new frame and screen in place and replaced the two screws. Total time to repair was less than 90 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Oak Park, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer would heat up but shut off too early
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from York, PA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint screen torn
Removed the lint screen, got a screw driver, removed two screws for the lint screen frame, installed the new frame, BAM done. One of the easyist repairs I made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- garrett from Oklahoma City, OK
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer lint trap was falling apart
I just changed the lint trap. the amazing thing was that I ordered the part one afternoon to be delivered USPS and figured I wouldn't see it for weeks. BAM! the next day I got this part in the mail. it was kinda weird. Are you guys living in my basement?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Frederick, MD
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint screen torn
Removed 2 screws from lint frame and replaced with new frame. Less than 2 minutes actually. Dropped in new lint basket and ready to go. Part arrived faster than expected. Website very easy to use. So pleased !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oviedo, FL
- Parts Used:
- 5303937186
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
gas dryer starts but no heat
after checking on line, i shut off the gas and disconnected the burner unit from dryer. after removing unit i tested all electronic parts and found the igniter was bad. i removed same and ordered new part. when new part was delv. i reinstalled the unit and all worked like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bel Air, MD
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint Screen was torn
Simply removed two Phillips head screws and the frame lifted right out. The new frame fit in the machine like a glove. Inserted the new screen and I was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Clovis, NM
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lint screen damaged
Removed two screws, installed the PERFECT fit replacement, and turned to a smiling wife. Done deal. Thanks for the really quick delivery.
Was this instruction helpful to you?
Thank you for voting!