DG600JXD1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George W. from Limon,, CO
- Parts Used:
- 5303931781, 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Support was worn out, tub shaft also.
Removed two screws in the inside of the front after opening the top by releasing the two clips. Front comes off of bottom clips easily. Drum can be removed and repairs made. Takes less than 30 minutes Be sure to remove door switch wire & unplug unit first. Drum belt can be re-installed easily thru the back access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philipsburg, MT
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
worn belt and squeaky bearring
remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kennedy from Fairhope, AL
- Parts Used:
- 5303307893, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Loud squeaking
Removed drum and replaced drum support bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Hueytown, AL
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
belt came off
removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from LONG BEACH, MS
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner Want Stay Light
Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Prattsburgh, NY
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer drum would not turn.
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from San Diego, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No heat.
Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!
Was this instruction helpful to you?
Thank you for voting!
Squeaking noise as the drum turned
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from fairfield, PA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Part
Really easy. 15 Minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from North Aurora, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Burner would not ignite
Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from FELCH, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no heat to dryer at startup
Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jay from youngstown, OH
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
easy
parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugenio from Lewiston, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
belt squeking.
Replaced belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from Hartland, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum belt was making a squealing noise, and it looked frayed.
Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs. Frances from Oklahoma City, OK
- Parts Used:
- 131390300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Just a lint screen (which I had replaced once before) but the local parts store wanted more than twice what this cost.
Easy, lint trap in front, unscrewed the old base, threw out the old lint screen which was hanging by a thread, and put the new (and - KEY WORD - cheaper) part in. All by Myswlf!
Thanks.
Thanks.
Was this instruction helpful to you?
Thank you for voting!