FSE747GES0 Frigidaire Dryer - Instructions

First of all I would like you all to know that I cheated just a bit. I had SEARS come out and tell me for sure what the problem was, as they took my dryer apart a payed close attention to everything they did. After I was told that it would cost me over $200 (on top of the $109 I just payed for them to tell me what was wrong) to fix the heating element. I replied with a "NO THANKS!", I also told them not to worry putting it back together. It seemed like he was very happy to hear that and thought I was going to buy a new dryer, he even gave me a coupon for a whole 10% off if I spend over $400. After spending 10 minutes or so on line I found the part I needed @ Partselect.com (plug-plug) for like $20. Once I received the part it took all of 15 minutes to take of the old and put on the new. First: Make sure power is off by unplugging or turn off breaker (can't finish a project if a project finishes you)! Second: Find the two power lines sticking out at about four o'clock and disconnect. Third: Unscrew porcelain separator and remove the two coil ends before removing the coil it's self from the arrow like holders. Forth: reverse last three steps with care (coil feels like it could break easily). Fifth: Place drum back in it's setting while making sure that the drive belt that turns drum is placed around motor pulley. Sixth: Button it up the way you pulled it a part. and your done, good luck!

Called a repair co. Said it would be about a week before he came to the rural area my mom lives and he probably wouldn't have the part. He would order it after he determined the problem. So I went to your web site and ordered the item it said was 80% and two other parts just in case. He came and used the Heating Element Assembly and said it was a good thing we had it. He would have had to order it and come back probably a week later. THANK YOU!! WE needed the dryer repaired sooner and saved another service call. I am returning the other parts not used and you make it so easy to do. I plan on using your site again.

It took about 3 seconds to slide on the new knob. Most important info here -- the new knob has a metal housing inside the plastic that should never strip like the old plastic-only knob. In other words, the new knob is superior to the original equipment. Also, delivery was very prompt. I'm very pleased - thanks!

Simply popped it back into place, careful not to break the new handle.

First I was shocked to receive my part the very next day after ordering. The new timer knob went on as easy as you please. I just matched the flat side of the spindle to the flat shaft of the timer knob.

Simple. Just order a new timer knob and fit perfect and snapped right on. Problem solved! = )

Just snap into place

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now

remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.

After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.

UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

The how to video was great. I had a little problem with getting the belt back on the pulleys. Not enough room for my hands. I did manage to get it back on ,and runs great