FDE847RBS0 Frigidaire Dryer - Instructions

I removed the gate in the back and found the belt had snapped. I continued to dismanlte the entire dryer to see what else was damaged. I pulled the drum out and ran the unit to make sure the motor didn't burn out and that the heater coil worked, which both did (I had no idea, this unit came with the house I purchased. They told me is was broken.) So after finding the belt broken I saw that the top felt guide was rubbed down so far that the plastic guides where in paper thin, craked pieces.

I used the manuel that came with the felt guide to glue the new one on. If you do not replace the lower felt guide as well, make sure you mash the top felt down so that it's level with the lower felt. after I got my unit assembled the top guide pulled away because I didn't do this.
Installing the belt is timely, but easy. remove the drum then lay the belt around the visible line that the old one creates. Use this site's diagram to affix it to the pull and motor and that's that. Rotate the drum with your hand to even the belt out all around the drum to prevent it wobbling. I did this installation by myself, but it would have been much much easier if I had a set of hands on the other side of the unit.
Parts all fit together by either sheet screws or clips. Just keep track of which screw goes where. some are different sizes.

Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

Based on all of the other posts, their explanations were right on, so I won't repeat it here. You could probably do this repair on your own, but it helps having someone to hold the drum while reattaching the screws. I replace the rear drum bearing assembly and the belt. I would recommend replacing the belt. I almost didn't, but I'm glad I did. Once I had it off, I could see the cracks in it.

When installing the new bearing, make sure that you pack it with the supplied grease. Be liberal with it. I used what left over grease I had to grease the idler puller bearings too.

The dryer works perfectly now, with no squealing. My experience with Parts Select was flawless. The shipping was extremely fast, and the parts were as described. Finding the correct parts was a snap thanks to their easy to use web site.

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

removed the old selector knob just pulled it out gently and lined up the new selector knob and gently pushed it into correct alignment. what a breeze.
reasonable prices. saved me $ on a service call, part, and labor. Thank you M



I just feel the postage is way too much for an item that weighs under 1 oz.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

only needed to attach knob with one hand.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

easy as pie remove handle add new handle tight screw took more time to find the philips head screw driver than to do the job

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.