FSG748GFS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Loren from Fergus Falls, MN
- Parts Used:
- 131264905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old plastic timer knob was stripped on the inside
It took about 3 seconds to slide on the new knob. Most important info here -- the new knob has a metal housing inside the plastic that should never strip like the old plastic-only knob. In other words, the new knob is superior to the original equipment. Also, delivery was very prompt. I'm very pleased - thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brooke from Brookline, MA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken knob
Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.
Thanks.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Mentor, OH
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J. from Lancaster, CA
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was wearing out.
Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Los Angeles, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
was using a pliers to turn the part without the knob on and off; just didn't cut it; my family told me about your website and it was EASY!
just put it on in 5 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from MENOMONIE, WI
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problem
Just snap into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karan from Charlestown, MA
- Parts Used:
- 131264905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the timer knob snapped off
Simple. Just order a new timer knob and fit perfect and snapped right on. Problem solved! = )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Pasadena, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Knob broke
First I used a pliers to remove the piece of the broken knob that was still attached to the shaft. Then I pushed the new knop onto the shaft until it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHLEEN from GARDEN GROVE, CA
- Parts Used:
- 131264905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob would not turn.
First I was shocked to receive my part the very next day after ordering. The new timer knob went on as easy as you please. I just matched the flat side of the spindle to the flat shaft of the timer knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from LONGMEADOW, MA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas dryer would generate heat at the beginning of the cycle but would stop after 5 min and would start making a buzzing noise.
Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelia from Elizabethtown, IL
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
replaced broken belt
Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherry from WATERVLIET, NY
- Parts Used:
- 134503600, 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Very noisy
Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from BELLEVUE, MI
- Parts Used:
- PCK2003
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dryer needed to be converted from natural gas to propane
The conversion kit had everything needed, However the instructions were lacking in description on how to assemble everything, this kit includes the new style burner, igniter, igniter mount, air shutter and propane orifices. A detailed picture would help.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SAGINAW, MI
- Parts Used:
- 5303937186, 5303931775, 5303281135
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
No heat to dry clothes.
There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.
Was this instruction helpful to you?
Thank you for voting!