FDG546RET3 Frigidaire Dryer - Instructions

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??

took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

i used one screw driver universal to pop off the cover then, i unscrewed the 2 screws off one on the left side and one on the right side, then useing the screw driver i popped off the left and right off the dryer houseing body their are 2 wires 2 unplug then at the back of the dryer theirs a vent 4 screw take then off then take off the belt then on screw the drum from in side pull out the drum,then 2 more wires to unplug now take off the blower housing with the motor and unscrewed the fan then your done. put it back the same way 15 to 30 mins

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

disconnected power unlocked both top sides ,lift top back and take top 2 screws out, then unhooked wiring,then remove whole front away from drum.scrap off all the remaining pieces, then glue and wait till tacky, then apply
front lower basket seal and top drum glide seal,replace the front ,hook wires back to proper place , put the two top screw back on!!! happy drying!!!

Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again

I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a bracket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.

Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.