DE700EDF2 Frigidaire Dryer - Instructions

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

followed vidio instruction which made it easy

Hired a professional!

followed the Video instruction which were provided. Dryer works like brand new.

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

Followed the video, it was good, the instructor's tips were useful and time saving.

I viewed the video from your site (Parts Select's) and followed those directions... which took the guess work out of the job and made it simple. Also the video alerted me to small ball bearing in the back which might have caused some head scratching if not for viewing the video. While everything was apart I did spend extra time cleaning. Many THANKS to Parts Select and the courteous parts person that I spoke with and placed my order with.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

The repair video from PartSelect.com was excellent in describing how to fix the dryer. All of the parts were included in the replacement kit, including the screws and ball bearing. I was very impressed with the quality of the kit and the video. A $25 kit probably saved me hundreds in repair cost and saved me from having to buy another dryer. Here's to another 14 years of use!

Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!