DE700EDD2 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cindy from Mauston, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squeeking when ran
Followed online video. All went smooth. Runs great!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Green River, WY
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
the drum was making wierd sounds like it was a worn out bearing
i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from edinboro, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
loud scratchy noise
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Aurora, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Drum Squeeking
Replace the Drum Bearing and Shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugenio from Lewiston, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
belt squeking.
Replaced belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from League City, TX
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Loud Squeeking
First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Opelousas, LA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
off balance and noisy operation
removed the drum out the front and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Murfreesboro, TN
- Parts Used:
- 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer tub started screeching and then dropped.
Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.
Was this instruction helpful to you?
Thank you for voting!
Squeaking noise as the drum turned
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from Hartland, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum belt was making a squealing noise, and it looked frayed.
Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Hudson, NH
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bearings Went and Idler Roller fell apart, not allowing drum to turn
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Prattsburgh, NY
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer drum would not turn.
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from seattle, WA
- Parts Used:
- 5303281154, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dryer had loud screeching noise
Followed the video on partselect web page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samantha from Portland, OR
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Rear Drum Bearing replacement
First I have to say that the video on the Parts Select website was invaluable, it truly made the replacement a no brainer. The kit came with everything I need and was a great price.
Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.
I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.
Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.
I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominico from Westerly, RI
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Drum didn't turn
Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks
Domenico Intrieri
Thanks
Domenico Intrieri
Was this instruction helpful to you?
Thank you for voting!