DG8800PW0 Frigidaire Dryer - Instructions

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

first I remove the top cover,then the front cover. Then slide in the belt. that it.

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

I unplugged the dryer. Undid the top by taking out 2 screws and mounts on each side of the back. There were two screws in the front panel that had to be removed. One on each side. Then I took the two wires off the killer switch on the door. Marking which was top and which was bottom. Then I removed the front panel. Then I undid the drum which had 3 screws in. I took out the drum to find the problem. I replaced the drum putting the belt on. Then I took off the back panel at the bottom of the dryer to get at the idler arm. Took off the spring and unhooked the arm. I put the new arm on and replaced the spring. I then put the belt on to the pulley and closed up the back panel. I put back the front panel. I put the top back on. I plugged it back in and turned it on and it worked!

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

All I did was push the new part into the machine! So easy!

Removed rear inspection plate, removed pulley spring and one hex bolt, replaced in reverse order. Very simple removal and install for this. Glad to see that Part Select still had parts for this 22 year old drier.

1. Slid putty knife under each side of front of dryer to release lid.
2. Removed 2 screws from front of drum to release door assembly.
3. Removed wires from door switch.
3. Cleaned lint out of inside of dryer.
4. Removed old felt seals, upper & lower.
5. Removed old glue with goof off type remover.
6. Glued new seals on & held then in place with clothes pins. (there was enough glue in the tube that came with the upper glide for both seals)
7. Put dryer back together.
**Ensure you verify the correct felt seal pieces with the model number of your dryer, usually on inside of door.

Removed 4 screws from 8" service panel from rear of dryer removed panel
Removed 4 screws holding rear of dryer top, removed rear brackets. compressed spring retainers on front of dryer top, removed dryer top.
Removed 2 screws from inside of dryer front, removed dryer front.
Removed old belt, cleaned machine, installed new belt on dryer drum, inspected rear service panel to insure belt had reached the drive motor.
Reinstalled front of dryer, being sure to hold drum up in position to match front panel..
Went back to rear service panel and installed belt on motor pulley and tension pulley.
Set top back on dryer, test ran dryer for short time to ensure all was functioning properly.
Installed dryer top, and brackets.
Installed service panel.

First of all, check the feedback on your parts installation at partselect.com. You can learn alot and make the job that much easier. I simply popped the top lid on the dryer, remove the electrical connections to the front panel shut off, then removed the screws and popped the tabs for the front panel to install the new belt around the drum. I then opened the back louvered panel to loop the belt correctly around the pulley and proceeded to reinstall both the front and top panels. The lint screen is a simple two screw installation with little or no issues. Once installation was complete the dryer fired up and the drum began to spin once again. A simple repair done at a great savings!

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

First I unpluged the machine, then opened the top with a flat head screw driver. Then I removed the two screws inside, unpluged the door sensor. (makes it stop when opened) Removed old gasket, cleaned with emery cloth, cleaned the residue and applied the glue provided. Waited about 1 min. and applied the new gasket leaving about 1/8'' of it hanging over the door facing the drum.