GLGR642CAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kristen from clearfield, UT
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken stem on on/off switch
just unplugged the old one, plugged in the new made sure it worked and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from San Diego, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No heat.
Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from FELCH, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no heat to dryer at startup
Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prince from Murfreesboro, TN
- Parts Used:
- 134844410
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Selector knob broke
Took it out of package..pushed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Botter from Livingston, TX
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drum was not turning
Removed access plate in rear, raised top panel, removed two screws holding front panel (with door) put new belt over drum. Threaded belt through path between motor drive and idler wheel. Put everything back together.
My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.
My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Bossier City, LA
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken belt and idler pulley
Removed top and front of dryer and rear panel. Installed belt and new idler pulley. Reinstalled top and front panel and rear panel. Dryer worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from North Aurora, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Burner would not ignite
Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jay from youngstown, OH
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
easy
parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.
Was this instruction helpful to you?
Thank you for voting!
Squeaking noise as the drum turned
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Hamilton, OH
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke. Had to use pliers to turn it on.
Really liked how easy it was to identify the part on your website, thank you.
Opened the package, pushed on the knob. FIXED! YEA, no more pliers!
Opened the package, pushed on the knob. FIXED! YEA, no more pliers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rochester, NY
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
Just put the the new one on. Parts select was easy to order and fast delivery thanks again.If I ever need a part i will be sure to come back to your site. Thanks so much... Mike Brooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madelyn from RIngtown, PA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob broke off and wouldn't turn on.
After receiving the part, I easily replaced it. I didn't need any tools and it took less than 2 minutes to fix. Also, the dryer seems to be working better altogether. Basically, I just inserted the knob where it was before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph m from orange, CA
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clothes Dryer Timer Knob cracked at stem
The repair was actually quite easy. I first removed the metal crimp ring that was left attached to the dryer Timer stem (was originally molded into the back of the Timer Knob which cracked) by pulling on it with pliers. The new Timer Knob just required a mild push onto the Timer stem of the dryer. Job finished. I'm back on the road to using my clothes dryer once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ED from Byron, IL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob cracked
pushed on new knob... Really fast shipping!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Everett, WA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turn-on knob broke.
Removed broken knob and installed the new by hand.
Was this instruction helpful to you?
Thank you for voting!