GLGR331CAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Beverly Hills, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced knob, perfect fit and match
just pushed new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Petaluma, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas dryer wouldn't stay hot.
I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).
The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
It works!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Mentor, OH
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Was this instruction helpful to you?
Thank you for voting!
2 of the dryers knobs had broken off
I ordered the knobs at less than half the price I paid before from the retailer. The knobs came in the mail very quickly. I took the knobs from the package and put them on. Easy repair, and I was especially happy with the ease of ordering and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLE from KINGWOOD, WV
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob cracked
put the new knob on
Was this instruction helpful to you?
Thank you for voting!
starter switch and knob broken
remove power cord from outlet . remove upper rear panel . remove 2 wires . remove old switch . . install new switch and wires , replace rear panel , install knob , plug in power cord and check dryer operation ok. 5 min job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Moultonboro, NH
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
temperature knob was broken
Just fix it in the groove and pushed it on and it was done in seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Thornton, CO
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
loud squeeling noise
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CUMMING, GA
- Parts Used:
- 134222900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from SANTA BARBARA, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle for dryer needed to be replaced.
Snapped the new door handle replacement from this site in place. Fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from TROUTDALE, OR
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broken
I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from BAKERSFIELD, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle on washer broke.
Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Apache Junction, AZ
- Parts Used:
- 134398300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The start switch was broken
Took the front off the dryer and removed the old switch and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan D from REDLANDS, CA
- Parts Used:
- 137551901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
the attached anchors and holes linled up about 80% of the time.
I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.
Was this instruction helpful to you?
Thank you for voting!