GLER642CAS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doug from TROUTDALE, OR
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broken
I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
Was this instruction helpful to you?
Thank you for voting!
Original drum belt broke
Watched the online video that showed how to replace the part. Was very easy to follow, but also I did open the inspection plate on the back to make it easier to put the belt on also to make sure that the spring and everything else look okay. As for the door switch took a photo with my phone of how the wires went on remove the wires, popped the old switch out put the new one in put the wires right back up the same way in my photo works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CUMMING, GA
- Parts Used:
- 134222900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from BAKERSFIELD, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle on washer broke.
Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLARK from JUNEAU, AK
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken knob
removed knob..very easy instructions..took 10 min...very pleased with repair and fast order...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from BUFFALO, NY
- Parts Used:
- 134398300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer start knob broke clean off
I YouTube'd how to repair it. It was super easy. Needed a power drill to get the screwsa off and a flat head screwdriver to pry off the wires but besides that it took about ten minutes and I was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Apache Junction, AZ
- Parts Used:
- 134398300
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The start switch was broken
Took the front off the dryer and removed the old switch and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Mount Horeb, WI
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start Knob Broke
My wife simply removed the knob from the package and pushed it on. No tools were needed and she felt satisfaction that she was able to "fix" the problem on her own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Middletown, NY
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Tumbler not moving
Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan D from REDLANDS, CA
- Parts Used:
- 137551901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
the attached anchors and holes linled up about 80% of the time.
I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from UXBRIDGE, MA
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken belt
Watched video sent to me after I purchased belt on line. Super helpful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Hewitt, TX
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken dryer belt
1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.
Was this instruction helpful to you?
Thank you for voting!
Could not do as video.
Had to open back side vent & use needle nose to secure spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ALBUQUERQUE, NM
- Parts Used:
- 134120900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
quit heating
The repair went smoothly considering I am a rookie. The repair videos on your site are great. Followed the techs instructions and got thru it fine.
Thanks,
Jim
Thanks,
Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ann from WALLA WALLA, WA
- Parts Used:
- 134120900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
lack of heat
Followed the video
Was this instruction helpful to you?
Thank you for voting!