GLER331CAS0 Frigidaire Dryer - Instructions

I basically looked on the back of the new knob and found the flat side.Then I match it to the flat side of the metal stud on the dryer .I then pushed it onto the stud on to the dryer.

old knob was broken so didn't stay on and work so had to use pleris to adjust temperatures when needed but now just put new knob on and we are in buisness and like new again!!! So glad I found your company and had the knob i needed and fast service!! thanks :)

installed new parts on the dryer in a natter of less than two minuted

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!

This repair took only about 15 seconds to complete. It just involved pushing the new knob on the selector. The provided video should give you the confidence to complete this task.. I invested $11.00 for the part. I would hate to see the cost to have a repairman come and fix this. Worth every penny

Unscrewed the back cover of the control console.
Unscrewed the one screw holding the facia plate to the control console at center of timer switch, then removed the start control knob and the heat selector control knob. Had to use a flat blade screw driver to wedge the heat selector knob off its spindle.
Although all screws removed, unable to remove facia plate due to plastic strip beneath it. Tried to remove the strip, held in by four tension points - one each end and two along the middle. Could not remove it without breaking the securing points off the back of the strip in the middle (plastic also).
After strip came off, easy to remove the facia. Identified the proper location of wiring attached to defunct start switch, and then removed the switch by turning clockwise a short distance.
Inserted the new switch, turned counterclockwise til it snapped into position.
Reversed steps to re-attach facia and back cover of control console. Despite the broken prongs in the middle, the plastic strip under the facia still stays in place by tension and is secured on the ends, so looks unnecessary to replace it. Bad design to not let you see how it is attached before you have to break it to get it loose!
Cleaned all surfaces and tested new start switch, which worked perfectly first try. Re-attached venting duct and repositioned dryer next to washer. Task completed.

Pulled the unit from the wall, Unpluged the power and removed the back cover behind the switches. twisted the switch removed and removed the wire, inserted switch and turned in place. Put the button on and good to go.

Let me start by saying, I ordered these 2 knobs for my dryer and they came faster than lightning. I was so glad to know that I could order something and have it within 48hours. KUDOS! Onto the actual item, I got the 2 knobs and since it was just the knobs that broke off and not the mechanism itself, I just took the knobs out of the package and put them on the mechanism by pushing on and VIOLA! , I was done!
If I ever need anymore parts for any of my other appliances I will sure use Parts Select and I will sure tell my friends about you guys too!!
Good Prices.. Fast Shipping.. gotta love it!

I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!

no story really received knob and popped the
knob on. parts select was wonderful. and received my part in a timely matter. and was reasonable. thank you parts select.

I was amazed that the knobs were received the next day. I took them out the box and put them in place. no tools needed. Thank you PartSelect.

Removed drum and replaced drum support bearing.

I used the posts on the site to ascertain the problem (fuze or element burnt out). The pictures were very helpful. I pulled the dryer to the floor and using my meter checked both the fuze and the element. The electrical diagrams were very helpful also. I took the dryer apart further to make sure the coil was indeed the problem. I then ordered the part!

My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).