GLEQ332CAS1 Frigidaire Dryer - Instructions

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!

I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!

Pulled the unit from the wall, Unpluged the power and removed the back cover behind the switches. twisted the switch removed and removed the wire, inserted switch and turned in place. Put the button on and good to go.

Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.

The heating coil wire broke and a section of it has become uncoiled. I had to remove the drum to access the heating coil. Disassembly was relatively easy. I took a good amount of time removing the excess lint all inside the dryer. The difficult part was re-installing the sheet metal screws as a few didn't want to cooperate due to burrs or slight misalignment.

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done

Removed drum and replaced drum support bearing.

I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!

Simply pulled the old knobs off & put the new ones on.

It is disappointing that the knobs cracked at all. I guess all the repair guys who've come out since our kitchen remodel are right - nothing lasts anymore & expect a repair within 5 yrs.

I ordered on a Monday & the knobs were delivered the next day, even though I chose only standard shipping. I was very, very pleased with PartSelect.com.

Very easy, slipped the old one off and placed the new one on

This was the greatest part ordering experience I think I have ever encountered.

No problems with ordering, arrived on time and works beautifully.

Removed the timer know and inserted the new one in its place. less than one minute work.

Excellent response and fast delivery from Parts Select.

Will use again, if necessary.

well guys replacing the knob was no big deal, but i initially thought that the timer was bad. i jumped the gun and ordered the timer on a wednesday and discovered on thursday upon further investagation that the back of the dial shaft was cracked creating the whole problem, so i ordered that and everything is fine once installed (& the timer is on the way back). my advice is check thoroughly and order once, you get less laughter from your wife on this one. thanx mcsgt(robert)

As simple as pulling off the old, broken knob and sliding on the new one. 20 seconds tops.

Ordering on Partselect.com was easy, and shipped fast. This was my second order with Partselect.com, and I will order from then again, when whatever else can go wrong, goes wrong!