FSEC849GHS0 Frigidaire Dryer - Instructions

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

First I unplugged the dryer. I removed the 3 knobs on the front control panel as well as the 6 screws on the back. The start switch easily removes by turning it 45 degrees and pulls out. I used a pair of needle nose pliers to pull the two connectors loose from the old switch. (They are color coded wires, 1 brown and 1 gray. The switch is marked with the numbers 1 and 2 on the connectors so remember which one goes where) Then i hooked up the new switch in reverse order and was back in business in about 5 minutes.

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.

While my wife was using the dryer, she noticed a loud sound and sparks coming from the bottom of the dryer (and an elctrical smell). The dryer stopped heating. When I started taking off the top and front of the dryer, I noticed what looked like a thermostat had melted and burned. I called a local part store and they said they would have to order it and it would take two weeks. But the guy was kind enough to give me the part number and told me to call anothe store. Instead I went online, found this site and the next day I had the part. It took me less than an hour to install it and reassemble the dryer. Me and my wife were very pleased.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

Girls you can do it on your own!

The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.

The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place.

It's a breeze!

Ordered the new knob and stuck it on. Doesn't get easier than that!

removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!

Simply put on the new knob. It took 2 seconds. Easy!!! So glad I didn't have to spend a small fortune for a repair. Thank you!

This was a Sears Dryer, also know as Kenmore, This dryer can be stacked or side by side. In this case it was stacked. There are no directions on how to replace this part. For this model made in 2005 the lid of the dryer is held in front by two clips. You open the lid simply by prying the two front corners up with a flat head screw driver. The front of the top lid pops right up. You may have to remove the mounts in back if you cant lift the dryer lid enough to be able to get your hands in. UNPLUG THE DRYER I got a nasty shock. There are two wires on the switch, remember how they go and where they are, that's important. Turn the switch (from the front or back) so that it pops out. Remove and replace the wires put it back in (from behind/top) and twist a 1/4 turn into place. Plug, test and simply push the cover back down onto the clips. Done.

I watched videos so I would know what I was doing. Well No, My thermostat was in the front of the dryer. But after a little blood and sweat, and I am not kidding, I got the front off. I ordered my new part. Finally got it in Spent $40.00 and it still doesn't work. I know it was the right part. I checked all the trouble shooting web site. That was the only thing they said it would be. Friends advice tell me it is the brains of the thing and I need a new one. Well not 2 weeks before Christmas. Thanks for asking. Single hard working mom.

used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap