FSEC447GHS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MICHAEL from IRONTON, MN
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drum belt broke
i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Alameda, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Both selector knobs broke within days of each other
The repair was simply removing metal guards from old knobs and placing the new ones on the dials.
What's remarkable, I ordered standard shipping and they were here the NEXT DAY~!
Great customer service.
fIA
What's remarkable, I ordered standard shipping and they were here the NEXT DAY~!
Great customer service.
fIA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrian from Denver, CO
- Parts Used:
- 131553900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace heating coil
The heating coil wire broke and a section of it has become uncoiled. I had to remove the drum to access the heating coil. Disassembly was relatively easy. I took a good amount of time removing the excess lint all inside the dryer. The difficult part was re-installing the sheet metal screws as a few didn't want to cooperate due to burrs or slight misalignment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Bellingham, WA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken start switch they used pliers and broke the stem
Pulled the unit from the wall, Unpluged the power and removed the back cover behind the switches. twisted the switch removed and removed the wire, inserted switch and turned in place. Put the button on and good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kennedy from Fairhope, AL
- Parts Used:
- 5303307893, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Loud squeaking
Removed drum and replaced drum support bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi Dixner from Nashville, TN
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
start knob broke off
I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Potosi, WI
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
control knob broke to starrt the dryer
simply pushed it onto the control
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from bayside, NY
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
on/off knob replacement
Piece of cake to remove old knob and replace with the new. Really impressed with delivery of the part the next day. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from CHINO HILLS, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace knob
took off old knob and put on new knob used my hands
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from Nacogdoches, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rotary knob broken/unable to turn on unit&end of cycle buzzer
Both rotary knobs broken and already removed. Just put knob back on spindle lining it up properly when putting on. Took less than 3 minutes--Yes!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamera from Fair Oaks Ranch, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotary knob broke
Just slipped it on --- easy as that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Coronado, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob on Dryer
Pulled broken knob off and pushed the new knob on. It was about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliot from Dedham, MA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Knob Broke Off.
Opened the package. Took out the new knob. Popped it on the old metal prong. Don't have to use the old pliers to start the dryer anymore. One of the little things around the house that was broken, just took a minute to order, a day or so to receive, a second to install and it was one more thing off my to do list. That was about the quickest and cheapest repair we made at our house this year.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARYAN from LOCKPORT, IL
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The start knob cracked and I had to start the dryer with pliers
I recieved the knob the next day after I ordred it. I just lined it up and snapped it on and I was good to go.
Was this instruction helpful to you?
Thank you for voting!