FSEC447GHS0 Frigidaire Dryer - Instructions

I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shake probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

Our heating element went out on our Frigidaire Affinity dryer. My husband is good at repairing things so we decided to order the part and do the repairs rather than hire a service technician. Before looking at the dryer we thought the back could be unscrewed and taken off to give access to the element but it did not. He had to take the dryer drum out to access the element. It was easy enough for him to do though and since we had everything opened up I was able to use the shop vac to get all lint cleaned out. I'm glad he did have to take the drum out after I realized the gasket on the exhaust pipe wasn't fitted on properly. There was some lint where there should not have been. Now that everything is clean and we have the new heating element installed we are good to go! The whole process of taking apart, installation and putting back together took about an hour and 15 minutes so not bad and we only had to pay for the part and shipping! Thanks PartSelect!

Ordered in new Element. (took apart dryer first and verified the coil on the old element was broken).

-Disconnected power
-Used flat blade screw driver and popped the top of the dryer off (two clips at front of the dryer on the door piece). Pull lid back and it will rest on its own.
-Removed two screws on the inside of the front door panel then used flat blade to pop four clips off. Lift up then out to removed door panel, drum will fall down.
-Removed small white plastic rest from front frame.
-Removed back silver vent to access motor. Pull the belt tensor away from assembly and pull belt out.
-Remove drum by grabbing belt and front of drum and forcing it up until it releases from the ball housing. Slide drum out of the front of frame/dryer.
-From here you can see the heating element. disconnect the coil wires (pull them). These are in series so it doesn't matter how they go back on. Disconnect the thermostat wires (X is negative lead).
-Removed the four screws from the back of the dryer to disengaged the element. Removed.
-Reassemble backwards.

snapped on new knob

Turned the knob to Start dryer one time too many and the knob broke in pieces. Got tired of using a set of pliers to start the dryer so Google was my friend. The install was quick and easy even if trying to decide what know what knob matched it took a while. But it was a perfect match (I bought an extra in case the knob on the 10 year old washer decided to do the same thing). The price was nice, the delivery fast and now you will have repeat customer who will mention this site to their friends if they need parts.

Pulled off the old knob, pushed on the new knob. It was that easy.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Pushed the new knob onto the shaft

I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.

Opened the package and pushed knob on,took about 2 minutes.

I removed the broken knobs and replaced them with the fresh ones.

The amazing part of the story was that my order was placed at 11:46 AM, shipped at 2:51 PM, and arrived early the following morning. Incredible service. Thank you!

Watched the online video that showed how to replace the part. Was very easy to follow, but also I did open the inspection plate on the back to make it easier to put the belt on also to make sure that the spring and everything else look okay. As for the door switch took a photo with my phone of how the wires went on remove the wires, popped the old switch out put the new one in put the wires right back up the same way in my photo works perfectly.

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

Easy as 1-2-3!