FER211CAS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anne from SANTA BARBARA, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle for dryer needed to be replaced.
Snapped the new door handle replacement from this site in place. Fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from TROUTDALE, OR
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broken
I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ann from WALLA WALLA, WA
- Parts Used:
- 134120900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
lack of heat
Followed the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from IRONTON, MN
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drum belt broke
i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrian from Denver, CO
- Parts Used:
- 131553900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace heating coil
The heating coil wire broke and a section of it has become uncoiled. I had to remove the drum to access the heating coil. Disassembly was relatively easy. I took a good amount of time removing the excess lint all inside the dryer. The difficult part was re-installing the sheet metal screws as a few didn't want to cooperate due to burrs or slight misalignment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Lafayette, LA
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped two gallon bottle of laundry detergent on dryer timer knob.
Found replacement with PartSelect. Ordered it and received it in less than a week. Took about 10 seconds to stick it on and I was back in business. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from SAN DIEGO, CA
- Parts Used:
- 137551901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
prolonged drying period and poor lint collection
removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci A. from Neptune, NJ
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Appeared to be a failed belt
Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Eldena, IL
- Parts Used:
- 5308015398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wont dry during one cycle, still doesn't
removed the two screws on the top at back of dryer then pryed up the front of the top, then removed the screws at the top of the front and pryed off the front of the dryer, the thermostat was at the bottom below the drum held on by two screws and had two wires on it. Fairly easy to replace but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Bellevue, NE
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer knob broke off
Husband is deployed and dd not have $100 for a repariman-So easy !!! Literally put the knob in the correct "D" position and pushed in with a little force. Took about 2 minutes from opening the package to starting my dryer.
Knob is not flush with the dryer-a small space in between knob and dryer but easy fix for $15.
Knob is not flush with the dryer-a small space in between knob and dryer but easy fix for $15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kennedy from Fairhope, AL
- Parts Used:
- 5303307893, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Loud squeaking
Removed drum and replaced drum support bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Raleigh, NC
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob Would Not Engage
Pushed the replacement knob onto the cycle selector. No tools required.
Technician was going to charge 65.00 to order the part (8.00) and push it onto the shaft/controller. He never called or showed up so I cancelled his service and did it myself. So glad the service person never showed. Saved 50.00!
Technician was going to charge 65.00 to order the part (8.00) and push it onto the shaft/controller. He never called or showed up so I cancelled his service and did it myself. So glad the service person never showed. Saved 50.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from clarksville, TN
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knob was shot.
took off the old one,and the inner sleeve and put on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from watertown, NY
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace timer knob
the part came very promptly - I opened the box & took out the knob walked to the dryer & pushed it in place , appreciate the great & honest service thank you
Was this instruction helpful to you?
Thank you for voting!