FEQ221CAS2 Frigidaire Dryer - Instructions

I used the posts on the site to ascertain the problem (fuze or element burnt out). The pictures were very helpful. I pulled the dryer to the floor and using my meter checked both the fuze and the element. The electrical diagrams were very helpful also. I took the dryer apart further to make sure the coil was indeed the problem. I then ordered the part!

Removed obvious screws to the vent etc. Then had a little trouble getting the cabinet open. My only problem was getting the front top panel off. A clip about 2" from either side at the top needs to be pushed in with a flat head screwdriver to release the top. Other than that the task was pretty straight forward. Two sets of wires to the heater itself. Used pliers to help pull them loose.

first i had a helper my 9 year old son. we came to this site and read a repair report and we used that to go by.once again my 9year old.

just unplugged the old one, plugged in the new made sure it worked and put it back together.

From opening the mailed package to complete installation of 3 knows took about 3 minutes total time very easy to order on you web site and the product came in so fast I thought that you were still processing the paperwork. Thanks keep it the services.

Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !

I popped the dryer lid open by pressing on two latches with the flat putty knife. I found that I really needed another set of hands, so my son helped me with this project. I had to disassemble the front panel by unscrewing 2 screws on the sides and also 2 screws around the dryer timer knob, after removing all knobs. Also, I had to pry apart 2 of the front pieces because they are clipped together with plastic latches. I unhooked two wires from the starter switch and then gave a half twist to remove it from the opening. Once that was removed, I just replaced it with the new part and put everything back together in reverse order. I did test the dryer before putting back together, but make sure you unplug it again while assembling. I forgot and two wires touched and there was a big spark and popping noise. Fortunately, nothing was blown out and no one was shocked I had absolutely no experience with anything like this but found this website to be a huge help. I figured everything out just be looking at the diagrams and some other notes on-line. Thanks!

I watched the video on the web site after selecting the part and it was pretty simple. Everything worked just like the video showed. Probably could have been done faster but I took time to vacuum the inside of the dryer out. Really liked the video.

Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.

Removed access plate in rear, raised top panel, removed two screws holding front panel (with door) put new belt over drum. Threaded belt through path between motor drive and idler wheel. Put everything back together.

My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

Removed top and front of dryer and rear panel. Installed belt and new idler pulley. Reinstalled top and front panel and rear panel. Dryer worked great.

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

as on the video. so easy. took longer to clean-up

The dryer was heating but the drum would not turn. We opened it up to see what the problem was. As soon as we opened it, we saw the belt was broken. I ordered a new one and after two trips to the laundromat I was ready to get the dryer fixed. That weekend we tackled the job. First I did a Google Search on Westinghouse dryer repair, found several ....one with a video:-) Punched in our model number and they went through the whole procedure....while it took them only 10 minutes, we took a little longer. But they had great ideas how to hold the drum while repairing, etc. Being recently laid-off this was a fantastic find. I have no idea how much a service call would be on the dryer nor could I afford a new one at this time.... Great old American Know How got it done.