FEQ221CAS1 Frigidaire Dryer - Instructions

The repair went very well for a 1st timer. Instructions were very easy to follow. Thanks

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.

Your tutorial video of how to change out the heating element was so helpful, it gave me the confidence to tackle it on my own. It was so detailed, there was no worries of not knowing what to do. Everything was exactly as the video showed, and was very easy to replace this heating element. My wife was thrilled we saved money on doing it ourselves, and grateful to have the dryer working with 3 kids and a husband who works in concrete! Thank You to the Parts Select team for putting such a helpful site for people to utilize!

I followed the vidio from yor web site it was great without it i would still be trying to get done.

With drum not turning, I removed rear access panel and confirmed that the belt was missing from the motor pulley. The instructional video provided by PS was extremely helpful. It made the job simple. Removal of drum thru front frame was the most difficult part which was relatively easy. Once the front panel and drum were removed, I could then see that the front drum top glide nylon/felt strip needed replacing which I then obtained.

Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

it was so easy using the video that you emailed me. I want to rebuild my whole drier now .

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

I never respond to any of these surveys, but in this case ill make an exception because they made it so easy and parts were received correctly a quickly. Thanks, dan

I am anything but an experienced handyman. I would always call the local appliance company to repair anything broken. This time money was a bit tight so I went on line to search directions to install a new heating element for our dryer. The PartSelect site was easy to navigate and with only the model number found the part I needed. Best of all the online instructional video so so detailed it made me believe I could do the repair. It took me less than 30 minutes to remove the burned out heating element. The new part arrived the next business day and was installed in another 30 minutes. It was so easy I feel guilty about all the other times I called service companies. Also, very upset about all the dollars I wasted. If and when any other appliance breaks, PartSelect will be the first place I will turn to. Thank you for giving me a new sense of pride in myself and saving at least $250.00. EDWARD

I unplugged the dryer from the power outlet and removed two screws from the back of the top cover and removed the cover. Then I laid the dryer down on its back for easy access to the screws on the bottom of the front side. I then removed two screws from the front bottom cover to clear the way for two more screws for the front main panel and door. Then I removed those two screws that attach the front panel and door to the dryer from the bottom of the dryer front. I then stood the dryer back up on its 4 pegs. I removed the top 4 screws connecting the control panel to the cross bar on top. Then I removed the two screws from inside the dryer accessing them from the top of the dryer, holding the front panel. With little and gentle force I pulled the front panel and door from the dryer housing, making sure not to loose the 4 snaps that come off with it. I removed two screws from the access panel to get access to the pulley in the lower back of the dryer. I loosened the tensioner by pushing it to the side and pulled the belt off the pulley. Next I needed to remove the drum which is connected by three screws in the center of the inside of the drum to a small plate on the outside that is attached to a ball that goes into a grease box. I then wiggled the drum out of the dryer. With some force I pushed the plate upwards to disengage it from the grease box and removed it. I unplugged the electrical wires connected to the thermostat and element. I then removed 4 screws from the back of the dryer that hold the heating element housing and removed the housing. I replaced the heating element and housing and the belt and put the dryer back in reverse order.

removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

It was a closet type washer/dryer combo. With little space to work I needed to know how to get at the heating element to test it. Was told the tumbler had to come out the front to expose the element. Made the job easy without having to figure that out.

First I watched the video available on the web site. After watching the video, I knew exactly what to do and how to do it. Really made the job a lot easier than it would have been. Some steps were harder to do than the video made them look but I atribute a lot of that to the fact that they were working in a large work shop and I was working in an area not a lot larger than the dryer. The hardest part of the job had nothing to do with changing the element, it dealt more with getting the vent hose off and on. Who ever designed the connection apparartus on dryers, used to connect that stupid hose to the back of it, must know something I don't. I have never had any luck when it comes to being able to get the hose connected and then getting the dryer back in the hole it came out of, without the hose falling off or getting crimped. PartSelect is a great company to deal with. Ordering was easy due to the highly intuitive web site and I got the part in two days. Saved me a lot of time running around town, burning a bunch of gas trying to find find what I needed. Thanks

The part fit perfect repair was simple thank guys for your help u are the best/removed the top/ front face /belt & drum removed old element installed new one dryer works perfect thanks again