FEQ221CAS1 Frigidaire Dryer - Instructions

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

I ordered replacement knobs...installed them, and the dryer was ready to go...no problem!!

Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.

Removed drum and replaced drum support bearing.

I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!

Removed top and front of dryer and rear panel. Installed belt and new idler pulley. Reinstalled top and front panel and rear panel. Dryer worked great.

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

The dryer was heating but the drum would not turn. We opened it up to see what the problem was. As soon as we opened it, we saw the belt was broken. I ordered a new one and after two trips to the laundromat I was ready to get the dryer fixed. That weekend we tackled the job. First I did a Google Search on Westinghouse dryer repair, found several ....one with a video:-) Punched in our model number and they went through the whole procedure....while it took them only 10 minutes, we took a little longer. But they had great ideas how to hold the drum while repairing, etc. Being recently laid-off this was a fantastic find. I have no idea how much a service call would be on the dryer nor could I afford a new one at this time.... Great old American Know How got it done.

as on the video. so easy. took longer to clean-up

My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).

I popped the dryer lid open by pressing on two latches with the flat putty knife. I found that I really needed another set of hands, so my son helped me with this project. I had to disassemble the front panel by unscrewing 2 screws on the sides and also 2 screws around the dryer timer knob, after removing all knobs. Also, I had to pry apart 2 of the front pieces because they are clipped together with plastic latches. I unhooked two wires from the starter switch and then gave a half twist to remove it from the opening. Once that was removed, I just replaced it with the new part and put everything back together in reverse order. I did test the dryer before putting back together, but make sure you unplug it again while assembling. I forgot and two wires touched and there was a big spark and popping noise. Fortunately, nothing was blown out and no one was shocked I had absolutely no experience with anything like this but found this website to be a huge help. I figured everything out just be looking at the diagrams and some other notes on-line. Thanks!

Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.

I watched the video on the web site after selecting the part and it was pretty simple. Everything worked just like the video showed. Probably could have been done faster but I took time to vacuum the inside of the dryer out. Really liked the video.