FGZ831CAS1 Frigidaire Dryer - Instructions

We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

I watched the video on the repair and followed it. Super easy. Repair only took 30 mins. Please note there are 2 glides. Make sure to order 2.

I just pushed the washer on its side on a price of wood. I put a pan to catch the drain water.It was then as easy as detaching two boots and two bolts that hold the drain motor on.Do it in reverse and you got it.Oh first don't forget to unplug the electrical wires ect.

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a bracket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.

Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.

The swap out was easy except for figuring out how to remove the timer knob off without breaking it so the faceplate can be removed and the switch can be swapped. In back of the timer switch with some needle nose pliers you pull a plastic pin back and hold it back. This will allow you to pull off the timer switch knob. However, the real problem was so simple I could kick myself. The COLD WATER PRESSURE WAS TOO STRONG. I simply turned down the cold water pressure some and the washer goes through all it's cycles. I really hope this helps someone else out there before they go buying parts or even a new machine. I did hours of internet research and I didn't come across this simple answer. I changed an electric water valve and a temperature switch before realizing it.

I found a you tube video that walked me thru the steps. Only problem encountered was 2 screws which were different and a little difficult, but became obvious as the control panel wouldn't loosen as video suggested. Otherwise the repair was fairly easy, and VERY SATISFYING.

removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced

I cut off the four that didn't line up - I suppose since this was a gasket that fit several makes, I should expect this type of problem.

Removed front and back panels as well as the dryer front, placed belt on drum and drive motor. I found that taking the door off the dryer front made the reassembly much easer.

I attempted to figure it out first but to no avail. Found an article on e-how and followed the steps to access the drum. Found your company on internet and called the 800 number to order the part. Delivery was quick (2 days) and it was the exact part. Thank you.

Unplugged dryer, removed access panel on the back of dryer. Removed access panel on the front of the dryer. Removed the front panel of the dryer. Inside the drum, removed the three screws on the center bearings. Slide the bearing out of the bearing support. Replaced the bearing support. Then reassembled the drum. Replaced the belt an reassembled the dryer. Two people would be recommended for reassembly.