FGQ221CAS0 Frigidaire Dryer - Instructions

I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!

You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.

The belt arrived in 2 days. I cleaned the inside and it took no time to replace the belt. All I did is removed the front.The video was very helpful.Your magnet is on my refrigerator for future orders. Thanks.....Andy

I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

I have used this company twice now and both times have been a good experience. Would highly recommend!

Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.

Installed just like the video described and it went quite well. The part arrived in a short amount of time and the belt was exactly what I needed.Thank you I will visit your web site again. A very satisfied customer. :) Veronica G.

Took the coils off and put the new one on thats all

Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

so easy my daughter installed it the video was very helpful

Check that power cord is still disconnected from initial inspection. Remove chassis cover plate. Count and set the screws aside. Check type and fit of replacement. Twist-lock new switch into place. Swap wires onto proper terminals of new switch. Replace cover plate. Replace and tighten switch knob. Re-connect power plug. Activate new switch. Three tests successful. Return dryer to ready position. Test again- OK. Repair complete.

Slowly my dryer began to stop worftking. I found myself wiggling the starter knob to make it work until it completely gave up. I took the model name and number and found a video describing how to replace the starter device. it took me about 20 minutes to make the change. it only took that long because I decided to clean out the interior thoroughly with a vacuum. All in all it was very easy.

Part Select got me the right parts in the agreed time--good job. Shut off the power or unplug the dryer which ever is easiest. The toughest part of doing this job was figuring out how the lid came off the dryer, if you have a jack knife or a putty knife you push it in between the top of the dryer and the body about an inch below the dryer top and about six inch from both sides of the dryer front you will hit a latch that releases the top--slip a screw driver into the opening and do the other side. The top can be removed or you can hold it open with a stick. There are two screws that you need to locate they are on the inside of the dryer front about 9" from the top one on each side they are all that hold the front on the body so remove them but carefully not to drop them inside the dryer. On my dryer there were two screw inside the dryer door that held the filter body onto the front that had to be removed too. Then push the screw driver between the front and the body of the dryer like the top and it will pop open. There are some wires going to the front from the body they can be unplug just follow the wires to the connection point. On mine, I squeezed the sides of the connector and the wires pulled apart. Now you can move the front aside. At the lower right in the body you find the valve and heater burner. On top of the valve there are two sets of wires coming off the valve. Disconnect the wires--one set is for a three wire connection the other for two wire connection. Your parts have a two wire coil and a three wire coil. The coils are freed by unscrewing the metal cover that holds them down remove the two screws and that cover then remove the old coil off the valve then replace the new coil with the part that is the same. Three pin coil with three pin coil positioning in the same way as the old coil, then do the other one. Reattached the metal cover with the screws and put it all back together in reverse order. The dryer chamber--the inside of the dryer rests on the front so when you put them together you may have to lift the chamber up to met the face a little (1/4"). Good luck.

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

There was no heat, the dryer worked in all respects but the flame did not come on to dry the clothes. I suspected the ignighter so I disconected the wire leading to the ignighter and tested the electrical connection with a regular tester used for testing 120 v ac circuits in a normal residential house outlet. I turned the dryer on and used the tester on the incoming electrical line that I disconnected from the ignighter there was power so I determined that the trouble was with the ignighter,it took about ten minutes to replace the ignighter after I received the part from partselect. The dryer worked fine with the new part. A fairly simple job to take the burner out and install the ignighter.