KER331ZAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Midlothian, VA
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
worn bearing
Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary T. from Bunn, NC
- Parts Used:
- 131553900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
heating element went out
first i had a helper my 9 year old son. we came to this site and read a repair report and we used that to go by.once again my 9year old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from Bowling Green, OH
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer wouldn't heat
Removed obvious screws to the vent etc. Then had a little trouble getting the cabinet open. My only problem was getting the front top panel off. A clip about 2" from either side at the top needs to be pushed in with a flat head screwdriver to release the top. Other than that the task was pretty straight forward. Two sets of wires to the heater itself. Used pliers to help pull them loose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Murfreesboro, TN
- Parts Used:
- 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer tub started screeching and then dropped.
Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Holly from Glen Gardiner, NJ
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Dryer Drum Belt
Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.
Was this instruction helpful to you?
Thank you for voting!
Dryer was squeking
I watched the video on the web site after selecting the part and it was pretty simple. Everything worked just like the video showed. Probably could have been done faster but I took time to vacuum the inside of the dryer out. Really liked the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Botter from Livingston, TX
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drum was not turning
Removed access plate in rear, raised top panel, removed two screws holding front panel (with door) put new belt over drum. Threaded belt through path between motor drive and idler wheel. Put everything back together.
My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.
My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from charlotte, NC
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
broken belt
I replaced this belt once before but it squeaked for over a year. This belt from Part Select was much better quality and now the dryer works perfectly, no squealing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Bossier City, LA
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken belt and idler pulley
Removed top and front of dryer and rear panel. Installed belt and new idler pulley. Reinstalled top and front panel and rear panel. Dryer worked great.
Was this instruction helpful to you?
Thank you for voting!
Squeaking noise as the drum turned
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from So. Hamilton, MA
- Parts Used:
- 134503600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer heated up but drum would not turn
The dryer was heating but the drum would not turn. We opened it up to see what the problem was. As soon as we opened it, we saw the belt was broken. I ordered a new one and after two trips to the laundromat I was ready to get the dryer fixed. That weekend we tackled the job. First I did a Google Search on Westinghouse dryer repair, found several ....one with a video:-) Punched in our model number and they went through the whole procedure....while it took them only 10 minutes, we took a little longer. But they had great ideas how to hold the drum while repairing, etc. Being recently laid-off this was a fantastic find. I have no idea how much a service call would be on the dryer nor could I afford a new one at this time.... Great old American Know How got it done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas F. from Whitmire, SC
- Parts Used:
- 134813600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
clothes hanging-up during the drying cycle,leaving marks on the garments.
as on the video. so easy. took longer to clean-up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Jasper, TN
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Noise in dryer
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
door handle an screws missing
doo handle snapped in place an replced screws that were missing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Baltimore, MD
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter bent
Vacuumed lint and inserted new filter.
Was this instruction helpful to you?
Thank you for voting!