GER221CAS0 Frigidaire Dryer - Instructions

Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.

I followed the vidio from yor web site it was great without it i would still be trying to get done.

I heard the dryer running, but I didn't hear it tumbling like usual, so I got suspicious. I popped the top off of the dryer to reveal a broken belt. Installation took 20 minutes.

With drum not turning, I removed rear access panel and confirmed that the belt was missing from the motor pulley. The instructional video provided by PS was extremely helpful. It made the job simple. Removal of drum thru front frame was the most difficult part which was relatively easy. Once the front panel and drum were removed, I could then see that the front drum top glide nylon/felt strip needed replacing which I then obtained.

Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

I first had a problem with the dryer not heating. When I looked at the heating coil I could see it was broken. With much work I replaced the heating coil. The real pain in the ass was reattaching the dryer drum back to the bearing on the back of the unit. It is very difficult to find the holes on the rotating bearing and line them up with the 3 holes in the drum to insert the screws. Hence my mistake, I evidently didn't tighten the screws tight enough as they would fall out after an hours use and destroy the new coil. I replaced the coil but still no heat. . . . When the coil shorted out it damaged other electronics. I replaced two parts of the electronic (thermal limiter and high limit thermostat). Still no heat. I have another almost identical unit so I pulled the control panel out of it and still no heat. There is one other electronic part I see that I am going to replace but at this point I would rather eat a can of worms then look at it. I would highly recommend to anyone performing this procedure to really crank the screws in the drum tight and use blue locktite.

First I watched the video available on the web site. After watching the video, I knew exactly what to do and how to do it. Really made the job a lot easier than it would have been. Some steps were harder to do than the video made them look but I atribute a lot of that to the fact that they were working in a large work shop and I was working in an area not a lot larger than the dryer. The hardest part of the job had nothing to do with changing the element, it dealt more with getting the vent hose off and on. Who ever designed the connection apparartus on dryers, used to connect that stupid hose to the back of it, must know something I don't. I have never had any luck when it comes to being able to get the hose connected and then getting the dryer back in the hole it came out of, without the hose falling off or getting crimped. PartSelect is a great company to deal with. Ordering was easy due to the highly intuitive web site and I got the part in two days. Saved me a lot of time running around town, burning a bunch of gas trying to find find what I needed. Thanks

I followed the great instructions that were provided by Partselect. There were no surprises. I took my time and it now works like new.

impossible to get to the screws without dropping them.the only way to replace the part was to over drill the holes and install from the rear of the dryer using small bolts and nuts.got bad cuts and scrapes from the sharp edges on the cabinet. after all this , it is still over heating. ordered the other part to fix and it looks like the front of the dryer has be taken off and the drum removed to fix it

The part fit perfect repair was simple thank guys for your help u are the best/removed the top/ front face /belt & drum removed old element installed new one dryer works perfect thanks again

I youtube'd the repair, and repaired it! While I was at it I replaced the belt! (Highly recommend replacing the belt while you are replacing the element!) Was a snap!

Had the drum bearing but had never got a round to putting it in we just let it squeek. Then the belt went. Easy enough, whatched the tutorial once and just did it. 35 minutes and back drying.

Took apart dryer and replaced limiter located on back, reassembled dryer and tested wiithout connecting to vent. Dryer working fine without vent connection. However as always something simple turns to disaster when children help. While cleaning out lint from dryer vent which I will say was the original problem causing the limiter to trip, youngest son wanted to help. Son did not know that to walk in an attic you must step on joists not drywall. No one was hurt just banged up falling into the garage. Extended repair to ceiling added dificulty factor of 2 days and a bit of insulation clean up. Good news is the dryer works fine and the vent is no longer clogged up with lint. Watch your help it always adds to the repair.

It was a closet type washer/dryer combo. With little space to work I needed to know how to get at the heating element to test it. Was told the tumbler had to come out the front to expose the element. Made the job easy without having to figure that out.