GEF331CAS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kristen from clearfield, UT
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken stem on on/off switch
just unplugged the old one, plugged in the new made sure it worked and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Jasper, TN
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Noise in dryer
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from Saugus, MA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked knob
I pushed the new knob onto the post.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from New Iberia, LA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Unhooked wires turned switch to the left put new switch in and turned it to the right 1/4 turn and put knob on front of switch this is the best parts web I have been on so far.
Was this instruction helpful to you?
Thank you for voting!
door handle an screws missing
doo handle snapped in place an replced screws that were missing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Baltimore, MD
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter bent
Vacuumed lint and inserted new filter.
Was this instruction helpful to you?
Thank you for voting!
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
Dryer drive belt broke
I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Sacramento, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Due to weather exposure, the handle fatigued and broke in several parts.
You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from Ripley, WV
- Parts Used:
- 131553900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating Element burned up/ No Heat
Pulled front off dryer, popped the top up, took belt off pulley, pulled drum up and out just far enough to pull element out and put new one in. Very easy and quick. PartSelect always sends good quality parts and very quickly. I will use them for all my repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Middlebury, VT
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken turn type start switch
just like the excellent video showed me. It was so easy and the web sight has a video to show me how to do it. Piece of cake! Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Renton, WA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The knob broke
I unplugged the 110 on the dryer, then popped the top on the dryer (with a screw driver), held the switch in place, bent the brass fittings to clamp the switch assembly to the front of the dryer panel and installed the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from San Diego, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was broken
Not much needed to replace a broken knob. I was very impressed with the fast service and will recommend Partselect to my friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- August from Las Cruces, NM
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
Pulled the old knob off to get part number. Ordered replacement part. When it arrived, I pushed the new knob on the shaft. It ain't rocket science! Thanks for you quick, efficient service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE*HUMPAL from CADOTT, WI
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob broke
I ordered a new knob, delivery was fast, and it slipped right on. Works perfect! Thanks, Diane
Was this instruction helpful to you?
Thank you for voting!