DE150JDF1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Brooksville, FL
- Parts Used:
- 5303281153, 5300622032
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
NO HEAT& drum not moving
googled frididaire dreyer parts
found Partselect
ordered parts {they were here in less time than what they stated}
watched Film {very helpful}
Me and My son installed both parts less than 1 hr.
VERY HAPPY WITH PARTS AND SERVICE
Will order from PartSelect when something else Breaks
VERY happy
Dave..
found Partselect
ordered parts {they were here in less time than what they stated}
watched Film {very helpful}
Me and My son installed both parts less than 1 hr.
VERY HAPPY WITH PARTS AND SERVICE
Will order from PartSelect when something else Breaks
VERY happy
Dave..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Opelousas, LA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
off balance and noisy operation
removed the drum out the front and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from League City, TX
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Loud Squeeking
First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Green River, WY
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
the drum was making wierd sounds like it was a worn out bearing
i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Prattsburgh, NY
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer drum would not turn.
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from edinboro, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
loud scratchy noise
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from fairfield, PA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Part
Really easy. 15 Minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Whitesboro, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screen ripped
2 screws (Philips) old one out, new one in, real easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Lexington, KY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the lint screen was old and holey. lint was getting into the dryer hose.
All I had to do was take out two screws that held the lint screen frame into the dryer, vacuum the opening to get the lint out that had accumulated, place the new frame in the opening, tighten the two screws that hold it in place, insert the lint screen and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Hudson, NH
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bearings Went and Idler Roller fell apart, not allowing drum to turn
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from roslyn, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint Filter was Torn
Removed old frame and filter. Slipped in the new frame and screwed it in. inserted the new lint filter.
Done in under 5 minutes.
Done in under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Gilbert, AZ
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen was torn
It took me all of 1 minute to take out the old lint screen and drop the new one back in.!!! I didn't need the frame. I had no idea that I could find a replacement so fast!!! Just wish I had not waited a month to look for one. Thanks for the fast service ! !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Piscataway, NJ
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Dryer
I did not think anyone would even carry the lint screen and frame for our OLD dryer. The price was reasonable and shipping was fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Jacobson from Coconut Creek, FL
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Screen ripped and shredded. Caused painful cleaning of lint.
Perfect match for part we needed. Popped out old, popped in new. Works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Two Rivers, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screen was torn
Removed two screws. Removed screen frame. Cleaned lint from ductwork. Inserted new screen frame and replaced screws. Done in 5 min.
Was this instruction helpful to you?
Thank you for voting!