FDG546LES0 Frigidaire Dryer - Instructions

OK, this is a follow-on repair story.. I *did not* order the lower basket seal when I ordered the upper basket seal... shame!!! BUT, I am now exceptionally quick at removing the front panel - less than 20 seconds!!!

For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.

I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.

Snapped the new door handle replacement from this site in place. Fits perfectly.

I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.

I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.

Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .

Just opened package and popped the part right in!

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!

The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

Pushed the new timer knob on the dryer. No tools were necessary.

Sooooo Easy. A no brainer. Just line up the knob and push it back on!

Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!