DE800EDW5 Frigidaire Dryer - Instructions

Removed two screws in the inside of the front after opening the top by releasing the two clips. Front comes off of bottom clips easily. Drum can be removed and repairs made. Takes less than 30 minutes Be sure to remove door switch wire & unplug unit first. Drum belt can be re-installed easily thru the back access panel.

All I had to do was pop in the new door catch. Works perfectly.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel

pulled dryer apart removed drum replaced bearing ass. and heat element and then put it back together. works great now. no squealing and heating great.

After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.

Removed drum and replaced drum support bearing.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

First I have to say that the video on the Parts Select website was invaluable, it truly made the replacement a no brainer. The kit came with everything I need and was a great price.

Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.

I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.

I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful

1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble

I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!

Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Replaced belt

Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.