DE7200ADD1 Frigidaire Dryer - Instructions

i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Removed front of dryer scraped old seal off ,used brake cleaner on a rag to get old glue off and roughed up seal area with sand paper ,spread glue on attached seal held in place with clothes pin overnight.

1)Unplugged unit from out let 2) Lifted top cover from base by prying up from the from the corners back is hinged 3) removed wires for door switch , removed a screw on the left and right from front. 4) pull front cover out from the top untill it clears drum then lift straight up off bottom clips. 5) scrape off old felt strip and guides 6) Sand untill all felt residue gone apply new glue to front cover wait a few minutes for glue to get tacky 7) clean out all the lint build up Checking from time to time that guide assemble is in place on front cover. 8) reinstall front cover when glue is dry.

* Clean off top of stackable dryer and remove top lid (pops off w/ screwdriver)
* Disconnect power supply and control wiring (right side under top lid)
* Remove left and right single screws securing front face of dryer
* Pop off dryer face w/ screwdriver
* Remove existing top glide from dryer face (peels off, use screwdriver or chisel/scraper to remove residue from felt and glue)
* Test fit new top glide
* Apply adhesive (included) to dryer face rim
* Clamp with 4 or so spring clamps and allow adhesive to set up (I waited about 30 minutes).
* Clean and inspect inside of dryer while the front face is off
* Clean dryer vent assembly (attached to dryer face)
* Reassemble and test easy rotation of the drum prior to use

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Removed top panel - disconnected harness from front panel- removed front panel- removed access door to belt tensioner on back panel - took belt off tensioner- removed drum removed upper felt with worn glide pads from front panel - removed most of old glue from panel (small file) and glued on new felt strip with glide pads - let sit to cure removed three phillips screws holding rear brg to the drum and removed brg - removed two phillips screws from rear panel holding plastic bracket, supporting bracket and back clip to the rear panel and replaced with new (use a drop of grease to hold the little ball brg in place during installation, make sure you don't loose it) install new brg to the drum (since they are self cutting screw difficult to install throught he drum, I "pre-cut" one of the threads then installed the rear brg to the drum, screw driver was of ratched type with a long extension - filled the plastic bracket with the grease - installed drum and front panel - tensioned the belt - installed top panel and access rear panel - done - I used the opprtunity to vaccum the interior of the dryer, lot of lint ----------------------------------------------------------------- there is a plastic guide on top of the heating elements which is burnt and should have been replaced but I could not find it in a catalogue. Anybody any idea? Also instructions for glide say to check the paint on the drum, what if it is damaged or gone?

We had the rear drum bearing replaced about three years ago. The company that serviced it was quick to take our money for the diagnosis but took over a month (and a threat to call the better business bureau) to actually make the repair. This time I decided to do it my self as I had successfully replaced the the drum drive belt two years ago. The dissassembly was challenging but the repair it's self very easy. I opted to use nuts and bolts to attach the bearing assembly rather than the supplied screws as they did not want to tighten. Reassmbly was a bit of a challenge regarding the drum drive belt but I had the entire repair done in less than an hour.

I took the front off, placed the belt quite easily.
I then had to unglue the old front drum seal and drum glide and re glue the new one, but it came with everything I needed so there was no problem.
My clothes no longer get these little brown stains they got. I suppose they were getting caught.

Its wonderful!!

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

Took out the drum by removing rear bearing and replaced with new one. Replaced top glides at same time.

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

Removed dryer top. Unscrewed the screw from each side inside the dryer the ones below the control panels. Don't unscrew those you will just have to put them back. Insert a flathead screw driver on the left side to loosen the front panel and slide it gently to the right. You can replace the drum glide without disconnecting any of the wires. Remove old drum glide and clean. Install new one and while the glue dries clean inside the dryer. Mine was very dirty!!!! Put everthing back and your ready to go. Don't forget to hook back the dryer vent. Thank you partselect my dryer is almost like new and is drying so much faster, no more noise and you have saved me lots of money.

Real simple, Unplug power cord from the wall outlet. Then open the top of the dryer by inserting a flat blade screwdriver under the front and pry up till the top snaps open. Lean the top to the back to keep it out of the way. Remove the 2 screws that held the front on and remove the wires for the door switch and the light. Remove the front by letting it lean out about 8 inches and lift it up out of the two bottom clips. Then just lay it any where it will be easy to work on. Clean where the new guide will go. Then just follow the instructions that came with the part. After the adhesive is fully dry just reverse the process and you are done.