FARG1011MW1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TERRY from MILLSBORO, DE
- Parts Used:
- 134197700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner Bad
Ordered part received next day fast shipping was great part in and working thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plymouth, IN
- Parts Used:
- 5303281135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Heat would come on but not stay on.
Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Otsego, MN
- Parts Used:
- 134587700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was not drying completly.
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from Silver City, NM
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The Heating System Of The Propane Dryer Stopped Working
When I direct the dryer exhaust into the room during the winter there is an external lint filter in the ducting. For some reason,enough lint got by the dryers filter and over a few cycles clogged the exhaust. I correctly assumed that the dryer overheated and some thermal limiter had opened up. The manual had exploded views and I located the limiter. Getting to it was another issue. The manual gave nbo instructions on getting to the limiter, but I had installed a propane conversion kit when I first got the dryer. It was necessary to remove the top, control panel, and front panel/door assembly. Disconnecting the gas line,some cable connectors, and a few screws allowed the removale of the burner assembly, then removal of the metal tube that surrounded the burner assembly and held a number of sensors, including the thermal limit, which, as expected, showed an open circuit. The replacement part was ordered and checked out as a closed circuit, which it should. Reassembly was the reverse. A little difficult to work in the cramped lower corner of the dryer. I'm 82 years old now but machines cannot beat me!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Irvine, CA
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Error code 66 - door open
Remove 2 screws at the upper rear attached to the top panel. Slide panel rear back and remove. Remove 2 screws attached to the front control panel. Lift panel upward. Remove 4 screws attached to the front panel (2 at the top, under the control panel, two at the very bottom). Lift front panel up and off, and unplug connector to door switch. Remove some more screws on the internal front panel edges, and the front to back brace holding up the control board. Lift panel up and out, and remove the drum, too. Thermal limiter located toward the rear, attached to the heating vent tube. Disconnect and replace. Re-assemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!