FDG216RBS2 Frigidaire Dryer - Instructions

Sooooo Easy. A no brainer. Just line up the knob and push it back on!

Pushed the new timer knob on the dryer. No tools were necessary.

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

popped in one in

When the part was delivered I opened the box and unwrapped the knob from the protective paper. I walked down the whole length of my hallway to the laundry room and carefully approached the dryer. Stealthily I reached across the top of the dryer and slid the knob onto the metal rod. Voila! I am now a certified Frigidaire Clothesdryer Repairperson!!

Slid on new knob. The turn around time on receiving the part was amazing. We were back in business within 2 days.

First of all, I LOVE Partselect.com.. The parts are reasonable, and arrive in a timely fashion.. The repair stories are far and away, one of the BEST features of this website - so hats off to the DIY'ers who have helped me overcome my challenges and helped me stay in the ..ahem.. "favorable" graces of my wife.. I need all the help I can get there.. Anyway, read the other repair stories first - LOTS of great insight.. I only have a couple pointers to add - below...

This is easily my 4th appliance repair project with Partselect.com, and I can say without a doubt that the experience has been positive every single time.. Until now.. I got the dryer torn down and realized that I SHOULD have ordered the SEAL-BASKET LOWER felt with my original order. When I inspected it for my list of parts to order, the upper glide was thrashed - no brainer.. I thought the lower felt was fine.. d'oh! I discovered this morning that I was wrong.. So, I JUST ordered the lower basket seal for *next* weekend.. (If you are gonna replace the original upper glide, replace the lower basket seal as well..) It'll be a slam dunk, though..

Now, for a couple useful tips:

If you are a car guy, get out your trusty can of brake parts cleaner to help clean off the old adhesive residue after you rip off the old upper glide felt. I also used a 1" plastic scraper to help facilitate removal, but the brake parts cleaner was a Godsend. I think I read someone else's suggestion to use "goof off" or whatever - but I couldn't find mine, so..... ...out came the brake cleaner... :) two thumbs up. Just use it sparingly - all those solvents are bad for children in California for some odd reason..

Spring loaded clamps to hold the felt down as the glue dries are also "nice to have". I used one on each end of the felt, and one for each of the teflon / plastic glides..

Finally - milk this job for all it's worth - it'll only take you 45-60 minutes or so... good luck...!!!

First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

I removed the cracked knob and attempted to replace with the new knob. Unfortunately my new knob did not fit. The internal diameter of the replacement knob was 2mm too small. I did not want to go through the hassle of returning and requesting another knob. So I just made it work. Thanks

First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer

took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer