FDE546NBS1 Frigidaire Dryer - Instructions

removed two screws - replaced lint screen replacement, TIME TO REPLACE UNIT - ONE MINUTE. What made this project a snap was the pictures and graphs( parts replace) uses to ensure you are ordering the exact screen .

After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.

UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.

With the excellent replacement parts sold by this site, it went like silk. The dryer is not only working great, but actually quieter.

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

replaced bearing and shaft new belt and everything works just fine

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

uncrew old, take out, put new in, screw in place.

Open the back plate. Broken pulley was already out of place. Put the spring on the pulley and placed it. It took me less than 10 min

When the part was delivered I opened the box and unwrapped the knob from the protective paper. I walked down the whole length of my hallway to the laundry room and carefully approached the dryer. Stealthily I reached across the top of the dryer and slid the knob onto the metal rod. Voila! I am now a certified Frigidaire Clothesdryer Repairperson!!

Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!