FDG436RES1 Frigidaire Dryer - Instructions

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

Very easy and straight forward repair.

Unplug the dryer and move it to a location that offers some room to work.

Use flathead screw driver to pop the front side top of the dryer up then lift the top of the dryer up to expose the drum.

Use phillips head screw driver to remove the two screws from the access panel on the rear of the dryer. Reach into the access area and remove the drum belt from the tensioner assembly. It's spring loaded so watch your fingers.

Disconnect the wiring harness at the right front of the dryer.

Remove the two screws that secure the front of the dryer to the sides.

Remove the front panel of the dryer by pulling the panel forward then up and off the two tabs at the bottom.

The felt strips and glides (which are worn off if you are doing this repair) are glued to the front panel of the dryer and now need to be removed. Removing the old felt will take some time and is the most difficult part of this whole repair.

Use some goof off or similar solvent adhesive remover to ease the removal of the felt. A putty knife will likely be helpful too.

Once the felt is off, wipe off any excess solvent and make sure the area to be re-felted is clean and dry.

Apply small serpentine bead of provided adhesive to the felt strips and glue the new strips on to the dryer. There is more than enough glue in the tube provided to get the job done. After applying felt strips, let them sit for about 30 minutes before reassembling dryer. You may want to use some light duty clamps to hold the felt in place while the glue sets but that's probably not necessary since the glue sets rapidly. Follow the directions on the glue tube.

Reassemble in opposite order.

Take the opportunity to vacuum out your dryer and give it a good inspection while you have it cracked open. You just might find those socks that disappeared.

Here are some "while your at it" ideas:

Replace both upper and lower felt strips.
Vacuum out entire dryer cabinet and the foam seal on the air box.
Replace drive belt.
Replace light bulb.
Replace bearing ball on rear of drum or apply some lubricant to the bearing.

I'm not saying do all these things, I'm just suggesting these items as things to consider based on the age and usage of your dryer.

This is an easy one person repair that requires no experience or special tools. Don't pay the repair man. Do it yourself.

All I did was push the new part into the machine! So easy!

Almost exactly as per the videos available on the PartSelect web site. The only additional information that would help is that the vent on the back of the unit can be removed to allow for access to the belt spring pulley. This avoids having to reach around from the front of the unit and feel your way to remove and re-install the belt.

used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

Checked PartSelect online for people with a. similar problem. Found most common problem was the coils.
I opened the top, removed the two screws holding the front panel, unclipped the wiring harness from the machine to the door and removed/cut the plastic wire tie and front came off easily. I put the front piece to the side after changing the light bulb. I cleaned out a large amount of lint and found the coils on the left hand side without trouble. Carefully disconnected the wiring clips, unscrewed the holding screw and removed the old coils. Installed the new colis, 1 has three prongs and the other has 2 so you ca'nt mix them up. Replaced the hold screw, re-connected the witing harness, installed a new wire tie, and re-stalled the two holding screws. Closed the cover and turned it on.
At first it did not heat up which was dissappointing; but then I left it alone and 15 minutes later it worked like new! And heated up just fine ever since.

Total cost about $35.00 with shipping. I took a chance that I would not need the sensor or the ignitor based on the comments of others and I just bought the coils. If I had to do it over I would have bought all three and saved on the shipping.

put the new one on

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

I remove the old lint filter and just put the new one in.