DE525MXW1 Frigidaire Dryer - Instructions

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

followed the Video instruction which were provided. Dryer works like brand new.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.

I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.

Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!

followed vidio instruction which made it easy

purchased bearing kit

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

The repair was done by my spouse. We replaced the rear drum bearing. We installed with the instructions sent by parts select. They were very accurate. The total repair took about 1 and 1/2 hours that was only because we cleaned out the entire dryer also, by using an air compressor to clean and blow out all the lint built up. This improved drying time and the part stopped the noise. I don't recall exactly what tools were used besides screwdrivers. This was our first time to replace anything in our dryer of 12 years old. I feel that if you follow the instructions that anyone would be able to do this repair. We did the repair in our garage because you need the room to work on it.

I watched the video and the instructions were perfect. The only thing I did differently was I had a second person help me to hold the bearing spring and hold the drum knob in place. I also used the rear access panel to disengage and re-engage the belt because I know I am not good at doing things blindly. You will definitely want to pre-thread the knob assembly before you screw it to the drum. Glad the kit included a bearing because the old one was completely gone. It took me so long because I took the opportunity to vacuum 10 plus years of lint and I was using it as a teaching opportunity. If I have to replace the heating element I think it will be much faster.

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint