FDE747GES0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Cumberland, RI
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clothing was getting caught between drum and front panel
First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike
Mike
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from PORTAL, GA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our door catch got lost inside the dryer after the door was slammed to hard
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BROOKLYN, NY
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Just popped the part I ordered right in and it's was closing in no time !
Just opened package and popped the part right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from FULLERTON, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle
I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from SANTA BARBARA, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic door handle for dryer needed to be replaced.
Snapped the new door handle replacement from this site in place. Fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from TROUTDALE, OR
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer door handle broken
I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
The new one just popped into place.
I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PORT CLINTON, OH
- Parts Used:
- 5303281153
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squeaking
Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lincoln from rio rancho, NM
- Parts Used:
- 5303283286
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rust Spots on the clothes....
OK, this is a follow-on repair story.. I *did not* order the lower basket seal when I ordered the upper basket seal... shame!!! BUT, I am now exceptionally quick at removing the front panel - less than 20 seconds!!!
For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.
For those who are considering doing this repair, there are more detailed explanations below - my only tip to help do this "quickly" would be to get some automotive brake cleaner to dissolve the old adhesive .. it is AMAZINGLY effective.. The best part is, don't worry about completely removing the old felt when you are tearing it off.. If some is still stuck to the door, it will actually hold some of the brake cleaner in contact with the old adhesive, which accelerates dissolving of the adhesive. Scrape it all off with a plastic scraper, and wipe it down a few times - surface is prepped & ready for the new adhesive + basket seal.. Use spring loaded clamps to hold the seal in place as you install it also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Smyrna, TN
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer leaving brown spots on clothes
First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth C. from Fort Valley, GA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clothes getting stuck in dryercausing brown stains on clothes
Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from tahlequah, OK
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bearing went out
took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kymd from Campobello, SC
- Parts Used:
- 134011703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The timer knob broke
Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- April from CARYVILLE, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy
Took it apart and installed the parts. Then I threw the dryer in the trash and bought a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PEDRO from BRONX, NY
- Parts Used:
- 131967600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the fan broke in half
i used one screw driver universal to pop off the cover then, i unscrewed the 2 screws off one on the left side and one on the right side, then useing the screw driver i popped off the left and right off the dryer houseing body their are 2 wires 2 unplug then at the back of the dryer theirs a vent 4 screw take then off then take off the belt then on screw the drum from in side pull out the drum,then 2 more wires to unplug now take off the blower housing with the motor and unscrewed the fan then your done. put it back the same way 15 to 30 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Verlin from Hampton, IA
- Parts Used:
- 5303281153, 131553800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum On The Dryer Quit Turning
1) I took a screw driver and pop the top lid up. 2) Took a philp screw driver and took 2 screws out of both sides of the front panal. 3) Lift up on the front panal and turned it out to the side. 4)Put the belt over the drum and on to the motor and tension pulley. 5) Put everything back together in reverse order starting with 3 ,2 and 1
Was this instruction helpful to you?
Thank you for voting!