FFT858980-B Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gale from Portland, OR
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squealing
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Meadow, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged lint screen
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A.J. from katy, TX
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner on for just 10 sec when started.
I tested continuity on parts like burner (ok) then on solenoids (not ok) timer (ok) I visited several websites and found the AppliancePartsPros.com site with FREE repair forum and found valuable advice. Then ordered my parts at Parts Select and were delivered 3 later at my front door.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Celia from El Paso, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer was tumbling, but not heating or drying clothes
There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from rembert, SC
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint screen was torn and badly bent and I could not find one locally.
Simply removed the two screws that hold the frame in place, removed the damaged parts, wiped down the surface area where the new one would mount and installed the new frame and screen in the reverse order from removal. SIMPLE and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Gilbert, AZ
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen was torn
It took me all of 1 minute to take out the old lint screen and drop the new one back in.!!! I didn't need the frame. I had no idea that I could find a replacement so fast!!! Just wish I had not waited a month to look for one. Thanks for the fast service ! !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Whitesboro, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screen ripped
2 screws (Philips) old one out, new one in, real easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Lexington, KY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the lint screen was old and holey. lint was getting into the dryer hose.
All I had to do was take out two screws that held the lint screen frame into the dryer, vacuum the opening to get the lint out that had accumulated, place the new frame in the opening, tighten the two screws that hold it in place, insert the lint screen and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Seminole, FL
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Lint Screen had come apart
Changed the old one for the new, But the best part was the fast service getting the part. I couldn't believe that I ordered it and three days later it was delivered. Good Job!!!! I will recommend you to everyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hope from Sanborn, IA
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
torn lint screen
It was extrememly easy, just pulled out the old screen and dropped in the new one. I didn't use the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from La Crosse, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dryer lint screen had a hole.
Pulled out old screen (exactly like what you do to empty it), put in new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christiaan from Saint Charles, MN
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Screen was becoming loose from its frame
No need to replace frame, just took the old screen out and slide the knew one in. About in two seconds its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Canton, MI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Torn Lint Screen
Replaced new Lint Screen. Changed Frame with two phillips screws. Total time spent: 3 minutes. Two day delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from omro, WI
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lint sreen started to fray
Quick and easy job, took 2 screws out from old frame and removed frame and lint screen. Really only needed lint screen as old frame in good shape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from SAN ANTONIO, TX
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screen filter damaged
took out two screws and removed old screen,relaced with new screen,and replaced two screws
Was this instruction helpful to you?
Thank you for voting!