FDE648GHT0 Frigidaire Dryer - Instructions

After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.

UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.

Replaced the heating element assembly. Problem was still there. Checked the electrical schematic to try to resolve. Everything checked out except the contacts on the motor M-1 to M-2 had no continuity. Removed the switch from the motor and exercised it. Works fine now.

Simply popped it back into place, careful not to break the new handle.

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.

I push the new knob onto the post that fit the knob

Just snap into place

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

popped the catch in existing hole and replaced the screws

Remove rear control panel cover and remove drum belt from pulleys. remove top cover by pushing in on the 2 hold down fasteners on the front with flat head srewdriver. remove front panel by removing the 2 screws and then pop it out by lifting up. disconnect the wires at the quick connect plugs and set the front aside. lift the drum up to pop it out of the bearing housing and move forward slightly to give youself good access to the wires for the heating element and disconnect the 2 wires. remove drum the reset of the way out and do your work. Replacing the heating pan and drum bearing is pretty obvious what to do. (just a few screws). remove thermal cutoff switch from old pan and install on new pan. reinstall in reverse. no need to label wires because it doesn't matter where the wires go an a switch (justs makes and breaks a circuit) and the heater doesn't matter as long as both wires are hooked up to complete the circuit. You can't mess up the quick connectors on the door. Only my heater failed but I also replaced the drum bearing as long as I had it all apart (only another ~$20). Take the time to clean out the dust from inside the dryer, it will help the blower motor run cleaner and cooler and last longer. I bought a belt also to have on hand for replacement. I didn't replace it since my old one was good and it is real quick to replace at a later time.

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

replaced bearing and shaft new belt and everything works just fine